ACPL-P456-000E Broadcom

ACPL-P456 and ACPL-W456 High CMR Intelligent Power Module and Gate Drive Interface Optocoupler Data Sheet Description Features The ACPL-P456 and ACPL-W456 contain a GaAsP LED optically Performance Specified for Common IPM Applications Over coupled to an integrated high-gain photo detector. Minimized Industrial Temperature Range propagation delay difference between devices make these Short Maximum Propagation Delays optocouplers excellent solutions for improving inverter Minimized Pulse Width Distortion (PWD) efficiency through reduced switching dead time. Specifications Very High Common Mode Rejection (CMR) and performance plots are given for typical IPM applications. High CTR Available in Stretched SO-6 Package with 8 mm creepage Functional Diagram and clearance Safety Approval: ANODE 1 6 V CC UL Recognized with 3750V for 1 minute (5000V RMS RMS for 1 minute for all ACPL-W456 devices and Option 020 N.C. 2 5 V O device for ACPL-P456) per UL1577 CSA Approved CATHODE 3 4 Ground SHIELD IEC/EN/DIN EN 60747-5-5 approved with V = IORM 1140V (ACPL-W456) and V = 891V Note: A 0.1 F bypass capacitor must be connected between peak IORM peak (ACPL-P456) for Option 060 pins 4 and 6. Specifications Truth Table (Positive Logic) Wide Operating Temperature Range: 40C to 100C LED V0 Maximum Propagation Delay t = 400 ns, t = 490 ns PHL PLH ON LOW Maximum Pulse Width Distortion (PWD) = 450 ns OFF HIGH 15 kV/s Minimum Common Mode Rejection (CMR) at V CM = 1500V CTR > 44% at I = 10 mA F Applications CAUTION It is advised that normal static precautions be IPM Isolation taken in handling and assembly of this Isolated IGBT/MOSFET Gate Drive component to prevent damage and/or AC and Brushless DC Motor Drives degradation which may be induced by ESD. Industrial Inverters Broadcom - 1 -ACPL-P456 and ACPL-W456 Data Sheet Ordering Information ACPL-P456 and ACPL-W456 are UL Recognized with 3750V (5000V for ACPL-W456) for 1 minute per UL1577 and are RMS RMS approved under CSA Component Acceptance Notice 5, File CA 88324. Option IEC/EN/DIN EN Part Number Package Surface Mount Tape and Reel Quantity 60747-5-5 RoHS Compliant -000E X 100 per tube -500E X X 1000 per tube ACPL-P456 Stretched ACPL-W456 SO-6 -060E X X 100 per tube -560E X X X 1000 per tube To order, choose a part number from the part number column and combine with the desired option from the option column to form an ordering part number. Example 1: ACPL-P456-560E to order product of Stretched SO-6 package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-5 Safety Approval in RoHS compliant. Example 2: ACPL-P456-000E to order product of Stretched SO-6 package in tube packaging and RoHS compliant. Option data sheets are available. Contact your Broadcom sales representative or authorized distributor for information. Solder Reflow Profile The recommended reflow profile is per JEDEC Standard, J-STD-020 (latest revision). Non-halide flux should be used. Regulatory Information The ACPL-P456 and ACPL-W456 are approved by the following organizations: IEC/EN/DIN EN 60747-5-5 (Option 060 only): Approved with Maximum Working Insulation Voltage V = 1140V IORM peak (ACPL-W456) and V = 891V (ACPL-P456). IORM peak UL: Approval under UL 1577, component recognition program up to V = 3750V (or 5000V for ACPLW456). File E55361. ISO RMS RMS CSA: Approval under CSA Component Acceptance Notice 5, File CA 88324. Broadcom - 2 -