ACPL-P481 and ACPL-W481 Inverted Logic, High CMR Optocoupler for Intelligent Power Modules and IGBT/MOSFET Gate Drive Data Sheet Description Features The high-speed ACPL-P481/W481 optocoupler contains a Inverted output type (totem pole output) GaAsP LED, a photo detector, and a Schmitt trigger that Performance Specified for Common IPM Applications Over eliminates the requirement for external waveform Industrial Temperature Range conditioning circuits. Short Maximum Propagation Delays The totem pole output eliminates the requirement for a pull-up Minimized Pulse Width Distortion (PWD) resistor. An Intelligent Power Module, Power MOSFET, or IGBT Very High Common Mode Rejection (CMR) can be driven directly. Hysteresis Propagation delay difference between devices has been Available in Stretched SO-6 Package. minimized to maximize inverter efficiency through reduced Package Clearance/Creepage at 8 mm (ACPL-W481) switching dead time. Safety Approval: (pending) UL Recognized with 3750V (5000V for RMS RMS Applications ACPL-W481) for 1 minute per UL1577. IPM Interface Isolation CSA Approved. Isolated IGBT/MOSFET Gate Drive IEC/EN/DIN EN 60747-5-5 Approved with V = IORM AC and Brushless DC Motor Drives 891V for ACPL-P481 and V = 1140V for peak IORM peak ACPL-W481, under option 060. Industrial Inverters General Digital Isolation Specifications Functional Diagram Wide Operating Temperature Range: 40C to 100C Maximum Propagation Delay t /t = 350 ns Anode 1 6 V PHL PLH CC Maximum Pulse Width Distortion (PWD) = 250 ns N.C. 2 5 V O Propagation Delay Difference: Min. 100 ns, Max. 250 ns Wide Operating V Range: 4.5V to 20V CC Cathode 3 4 Ground SHIELD 20 kV/s Minimum Common Mode Rejection (CMR) at V CM = 1000V Note: A 0.1 F bypass capacitor must be connected between pins 4 and 6. CAUTION It is advised that normal static precautions be taken in handling and assembly of this Truth Table (Inverting Logic) component to prevent damage and/or degradation which may be induced by ESD. V LED 0 On LOW OFF HIGH Broadcom - 1 -ACPL-P481 and ACPL-W481 Data Sheet Ordering Information ACPL-P481/W481 is UL recognized with 3750/5000V for 1 minute respectively per UL 1577. Both are approved under CSA RMS Component Acceptance Notice 5, File CA 88324. Option IEC/EN/DIN EN Part Number Package Surface Mount Tape and Reel Quantity 60747-5-5 RoHS Compliant -000E X 100 per tube -500E X X 100 per tube ACPL-P481 Stretched ACPL-W481 SO-6 -060E X X 100 per tube -560E X X X 100 per tube To order, choose a part number from the part number column and combine with the desired option from the option column to form an ordering part number. Example 1: ACPL-P481-560E: Stretched SO-6 Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-5 Safety Approval and RoHS compliant. Example 2: ACPL-P481-000E: Stretched SO-6 Surface Mount package in tube packaging and RoHS compliant. Option data sheets are available. Contact your Broadcom sales representative or authorized distributor for information. Recommended Pb-Free IR Profile The recommended reflow profile is per JEDEC Standard, J-STD-020 (latest revision). Non-halide flux should be used. Regulatory Information The ACPL-P481/W481 is approved by the following organizations: IEC/EN/DIN EN 60747-5-5 (Option 060 only): Approved with Maximum Working Insulation Voltage V = 891V for IORM peak ACPL-P481 and V = 1140V for ACPL-W481. IORM peak UL: Approval under UL 1577, component recognition program up to V = 3750V (5000V for ACPL-W481). File E55361. ISO RMS RMS CSA: Approval under CSA Component Acceptance Notice 5, File CA 88324. Broadcom - 2 -