8406 Wicking Grade Cyanoacrylate Adhesive 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION Product Name: 8406 Wicking Grade Cyanoacrylate Adhesive Product Type: Cyanoacrylate Adhesive Part Number: 8406 Available Sizes: 8406-20 20 mL 8406-50 50 mL 8406-500 500 mL Company Address: ChemTools Pty.Ltd. PO Box 463, Emu Plains, NSW 2750 Ph: 02 4735 3126 EMERGENCY PHONE: Australia: Poisons Information Centre 13 1126 International: Infotrac (708) 918 1900 2. COMPOSITION/INFORMATION ON INGREDIENTS Hazardous components CAS % ACGIH TLV OSHA PEL Ethyl cyanoacrylate ester 7085-85-0 90-95 0.2 ppm TWA None 3 3 hydroquinone 123-31-9 0.1-1 2mg/m TWA 2mg/m TWA 3 4mg/m STEL 3. HAZARDS IDENTIFICATION Hazard Classification: Hazardous according to the classification of NOHSC. This material is classified as Irritant (Xi) Risk Phrase(s) R36/37/38 Irritating to eyes respiratory system and skin. Safety Phrase(s) S2 Keep out of reach of children. S23 Do not breathe vapour. S24/25 - Avoid contact with skin and eyes. S26 - In case of contact with eyes, rinse immediately with plenty of water and seek medical advice S28 - After contact with skin, wash immediately with plenty of soap suds. S37/39 - Wear suitable gloves and eye/face protection. S46 - If swallowed, seek medical advice immediately and show this container or label. Relevant routes of exposure: Skin, Inhalation, Eyes Potential Health Effects Inhalation: May cause respiratory tract irritation. Skin contact: May cause allergic skin reaction. May cause skin irritation or burns. Bonds skin rapidly and strongly. Eye contact: Contact with eyes will cause irritation. Vapour irritating to eyes and mucous membranes above TLV Ingestion: Not expected to be harmful by ingestion. 4. FIRST AID MEASURES Inhalation: Remove to fresh air. If symptoms develop and persist, get medical attention. Skin contact: Wash with soap and water. Do not pull bonded skin apart. It may be peeled apart using a blunt object (eg a spoon). Acetone may be used to dissolve the cured adhesive. Remove contaminated clothing and shoes. Wash clothing before reuse. Get medical attention if symptoms occur. Eye contact: Flush with copious amounts of water, preferably lukewarm, for at least 15 minutes, holding eyelids open all the time. Get medical attention. Ingestion: Do not induce vomiting. Keep individual calm. Obtain medical attention. 5. FIRE-FIGHTING MEASURES Chemtools P/L Unit 4, 3 Pullman Place Flash point: Greater than 70C (160F) Tag closed cup Emu Plains, NSW 2750 Auto ignition temperature: Not available Flammable/Explosive limits-lower %: Not determined Phone: 02 4735 3126 Flammable/Explosive limits-upper %: Not determined Fax: 02 4735 3746 Extinguishing media: Foam, dry chemical or carbon dioxide. Special fire fighting procedures: None info chemtools.com.au Unusual fire or explosion hazards: None Hazardous combustion products: Oxides of carbon. Oxides of nitrogen. Irritating organic vapours. www.chemtools.com.au Material Safety Data Sheet 8406 Wicking Grade Cyanoacrylate Adhesive 6. ACCIDENTAL RELEASE MEASURES Environmental precautions: Polymerise with water and scrape up. Use PPE if spill is large. Prevent product from entering drains or open waters. Clean-up methods: Soak up with inert absorbent material (eg sand, earth, vermiculite). Store in a partly filled, closed container until disposal. Dispose of solid residues in accordance with relevant State and Federal requirements. 7. HANDLING AND STORAGE Handling: Avoid contact with eyes, skin and clothing. Avoid breathing vapour and mist. Wash thoroughly after handling. Storage: For safe storage, store at or below 24C (75F). Keep in a cool, well ventilated area away from heat, sparks and open flame. Keep container tightly closed until ready for use. Incompatible products: Refer to Section 10. 8. EXPOSURE CONTROLS / PERSONAL PROTECTION Engineering controls: No specific ventilation requirements noted, but forced ventilation may still be required if concentrations exceed occupational exposure limits. Respiratory protection: Use NIOSH approved respirator if there is potential to exceed exposure limit(s). Skin protection: Use impermeable gloves and protective clothing as necessary to prevent skin contact. Neoprene gloves. Butyl rubber gloves. Natural rubber gloves. Eye/face protection: Safety goggles or safety glasses with side shields. See Section 2 for exposure limits. 9. PHYSICAL AND CHEMICAL PROPERTIES Physical state: Liquid Colour: Clear Odour: Mild Vapour pressure: Less than 5 mm Hg at 27C (80F) pH: Not applicable Boiling point/range: Greater than 149C (300F) Melting point/range: Not available Specific gravity: 1.1 at 23.9C (75F) Vapour density: Not available Evaporation rate: Not available Solubility in water: Slight. Polymerises in the presence of water. 10. STABILITY AND REACTIVITY Stability: Stable. Hazardous polymerization: Will not occur. Hazardous decomposition products: Oxides of carbon. Oxides of nitrogen. Irritating organic vapours. Incompatibility: Strong oxidizers. Free radical initiators. Strong reducing agents. Alkalies. Oxygen scavengers. Other polymerisation initiators. Copper. Iron. Zinc. Aluminium. Rust. Conditions to avoid: SeeHandling and Storag (Section 7) andIncompatibilit (Section 10). 11. TOXICOLOGICAL INFORMATION Acute: Ingestion: Cyanoacrylates are considered to have relatively low toxicity. This material will rapidly polymerise in the mouth. Skin: Irritating to the skin. Bonds skin rapidly. Eyes: Contact with the eyes will cause irritation. The material will bond eyelids. In a dry atmosphere, vapours may irritate the eyes. Inhalation: Inhalation of vapours can cause respiratory irritation. Chronic: Prolonged exposure to high concentrations of vapours may lead to chronic effects in sensitive individuals. Chemtools P/L Product toxicity data: Acute oral LD50 greater than 5,000 mg/kg (rat). Unit 4, 3 Pullman Place Acute dermal LD50 greater than 2,000 mg/kg (rabbit). Emu Plains, NSW 2750 Phone: 02 4735 3126 12. ECOLOGICAL INFORMATION Fax: 02 4735 3746 Ecological information: Do not allow material to contaminate the soil or waterways. info chemtools.com.au www.chemtools.com.au Material Safety Data Sheet