CR5410-300 CR Magnetics

AC/DC Hall Effect Current Transducer The CR5400 Series, AC/DC Hall Effect Current Transducers, DIN RAIL / PANEL MOUNT, TRACING OUTPUT are designed to provide a bipolar output that proportionally reflects (traces) the waveform of the input current. These devices are specifically targeted to be used in applications where multi-mode current sensing is required. Applications Inverter and multi-frequency drives Multi-mode ground paths carrying both AC and DC signals Feed back loop building block CR5410 CR5411 Features Output isolated from input Single Element - .79 Window Non-contact current sensing 20 TO 600 AAC/DC Input Range 35mm DIN Rail or Panel Mount Connection diagram printed on case C Regulatory Agencies Constructed to meet UL 61010B-1 Constructed to meet CAN/CSA-C22.2, No. 61010-1-2004 Meets requirement of IEC 61010-1 and BS EN 61010-1 E199795 All single phase current transducers are available in split core design. Simply put an S at the end of the prefix* I.E. CR5410S-30 Add suffix for input range 20 - 20 AAC/ADC PART NUMBERS 30 - 30 AAC/ADC 50 - 50 AAC/ADC CR5410(S) Single Element with 5 VAC/DC output (split core design) 75 - 75 AAC/ADC - 100 - 100 AAC/ADC CR5411(S) Single Element with 10 VAC/DC output (split core design) - 150 - 150 AAC/ADC NOTE: AC/DC Split Core Transducers Available in 20 Amps and Higher 300 - 300 AAC/ADC Ranges available up to and including 600 AAC/ADC The Professional Energy Monitoring Company 3500 Scarlet Oak Blvd. St. Louis MO USA 63122 V: 636-343-8518 F: 636-343-5119 M N TI Web: Transducers AC/DC Hall Effect Current Transducer DIN RAIL / PANEL MOUNT, TRACING OUTPUT SPECIFICATIONS Frequency Range:.........DC to 4 KHz Basic Accuracy:....................... 1.0 % Output:........................... 5 Vac/DC or 10 Vac/DC Linearity:................................... 10% to 100% FS Output Load:................... 2 K or greater Thermal Drift:........................... 500 PPM/C Relative Humidity:......... 5% to 95%, Non-Condensing Operating Temperature:........... 0C to +50C Supply Current: Installation Category:............... CAT II CR5410:........................ Typical 35mA Max 40mA Vibration Tested To:................. IEC 60068-2-6,1995 CR5410S:..................... Typical 30mA Max 35mA Pollution Degree:..................... 2 Torque Specs.:.............. 3.0 inch lbs. (0.4Nm) Altitude:................................... 2000 meter max. Weight:.......................... 0.5 lbs. Insulation Voltage:................... 2500 VDC Cleaning:................................. Water-dampened cloth MTBF:..................................... Greater than 100K hours Supply Voltage:....................... 24 VDC 10% C + 1 26.6 + 2 9 1.05 3 8 OUTPUT 4 7 - 6 + - 3.3 5 DIN RAIL 73.1 .13 MOUNTING 2.88 SUPPLY Optional CLIP Mounting 83.3 - 3.28 20.1 41.8 .79 1.65 CR5410 5 VAC/VDC Output CR5411 10 VAC/VDC Output 76.6 3.02 50.7 2.00 5.6 CONNECTION DIAGRAM .22 TYP 88.7 3.49 25 .98 28.3 1.12 36.6 CRPS24VDC - 120 CRPS24VDC - 240 1.44 OUTLINE DRAWING Power Supply NOTE: The building installation must have a switch or circuit-breaker that is in close proximity and within easy reach of the operator. The switch or circuit breaker shall be marked as the disconnecting device for the equipment. The Professional Energy Monitoring Company 3500 Scarlet Oak Blvd. St. Louis MO USA 63122 V: 636-343-8518 F: 636-343-5119 M N TI Web: