PI90LV9637 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 LVDS High-Speed Differential Line Receivers Features Description Signaling Rates >400Mbps (200 MHz) The PI90LV9637 is a differential line receiver that use low-voltage differential signaling (LVDS) to support data rates in excess of 400 Single 3.3V Power Supply Design Mbps. These products are designed for applications requiring Accepts 350mV (typical) Differential Swing high-speed, low-power consumption and low noise generation. Maximum Differential Skew of 0.35ns A differential input signal (350mV) is translated by the device to 3V Maximum Propagation Delay of 4.7ns CMOS output level. Low Voltage TTL (LVTTL) Outputs Applications Industrial Temperature Operating Range: -40C to 85C Applications include point-to-point and multidrop baseband data Open, Short, and Terminated Fail Safe transmission over controlled impedance media of approximately 100-ohms. The transmission media can be printed circuit board Meets or Exceeds ANSI/TIA/EIA-644 LVDS Standard traces, backplanes, or cables. Packaging (Pb-free & Green available): The PI90LV9637provides new alternatives to RS-232, PECL, and -8-Pin SOIC (W) ECL devices for high-speed, point-to-point interface applications. -8-Pin MSOP (U) PI90LV9637 8-Pin W,U 08-0295 PS8667C 11/11/08 1PI90LV9637 LVDS High-Speed Differential Line Receivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Absolute Maximum Ratings (see Note 1, Page 4) Function Table Dtifferential Inputs Outpu Supply Voltage (V ) ....................................... 0.3V to +4.0V CC Input Voltage (R , R ) ............................... 0.3V to +3.9V IN+ IN- R , R R IN+ IN OUT Enable Input Voltage (EN) ...................... 0.3V to (V +0.3V) CC V 1H00mV ID Output Voltage (R ) .......................... 0.3V to (V +0.3V) OUT CC 100mV < V< 100mV ID S Package .................................................................... 750mW V L100mV ID Derate S Package ................................ 8.2mW/C above +25C OHpen Storage Temperature Range .......................... 65C to +150C Lead Temperature Range Soldering (4s) ...................... +260C Maximum Junction Temperature .................................. +150C ESD Rating ................................................................... 10kV Pin Description Note: Nname Descriptio Stresses greater than those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and R TTL/CMOS receiver output pins OUT functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not R Non-inverting receiver input pins IN+ implied. Exposure to absolute maximum rating conditions for extended R Inverting receiver input pins periods may affect reliability. IN GnND Ground pi V Positive power supply pin, +3.3V 10% CC Recommended Operating Condition M.in.T.ypMsax Unit Supply Voltage (V)0+33.+63. +3. CC V RDeceiver Input VoltageG0N +3. Operating Free Air 540+52 +C8 Temperature (T ) A 08-0295 PS8667C 11/11/08 2