48P570240050SPA Finder

48 SERIES 48 Relay interface modules 8A SERIES 2 CO forcibly guided contacts relay interface 48.12 modules,15.8mm wide Type 48.12 - 2 CO 8A - Screw terminals Relay with forcibly guided contacts according to EN50205 Type B 35mm rail (EN60715) mounting Cadmium-free contact material B 48.12 2 CO 8A Screw terminal Forcibly guided contacts relay Screw terminals According to EN50205 only 1 NO and 1 NC (11-14 and 21-22 or 11-12 and 21-24) shall be used as forcibly guided contacts. 48.12 For outline drawing see page 9 Contact specification Contact configuration 2 CO (DPDT) Rated current/Maximum peak current A 8/15 Rated voltage/ Maximum switching voltage VAC 250/400 Rated load AC1 VA 2000 Rated load AC15 (230VAC) VA 500 Single phase motor rating (230VAC) kW 0.37 Breaking capacity DC1: 30/110/220V A 8/0.65/0.2 Minimum switching load mW (V/mA) 500 (10/10) Standard contact material AgNi Coil specification Nominal voltage (U ) VAC (50/60Hz) N VDC 12 - 24 Rated power AC/DC VA (50Hz)/W /0.7 Operating range AC DC (0.751.2)U N Holding voltage AC/DC /0.4U N Must drop-out voltage AC/DC /0.1U N Technical data 6 Mechanical life AC/DC cycles /1010 3 Electrical life at rated load AC1 cycles 10010 Operate/release time ms 10/4 Insulation between coil and contacts (1.2/50s) kV 6 (8mm) Dielectric strength between open contacts VAC 1500 Ambient temperature range C 40+70 Protection category IP 20 Approvals relay (according to type) 1 X-2016, www.findernet.com48 SERIES 48 Relay interface modules 10A SERIES 1 CO relay interface modules, 48.P3 48.31 15.8mm wide Ideal interface for PLC and electronic systems Type 48.P3 - 1 CO 10A - Push-in terminals Type 48.31 - 1 CO 10A B - Screw terminals AC coils or DC sensitive coils 1 CO 10A 1 CO 10A Supply status indication and EMC coil Push-in terminals Screw terminals suppression module as standard Identification label UL Listing (certain relay/socket combinations) 35mm rail (EN60715) mounting Cadmium-free contact material 48.P3 48.31 Push-in terminal Screw terminal For outline drawing see page 9 Contact specification Contact configuration 1 CO (SPDT) 1 CO (SPDT) Rated current/Maximum peak current A 10/20 10/20 Rated voltage/ Maximum switching voltage VAC 250/400 250/400 Rated load AC1 VA 2500 2500 Rated load AC15 (230VAC) VA 500 500 Single phase motor rating (230VAC) kW 0.37 0.37 Breaking capacity DC1: 30/110/220V A 10/0.3/0.12 10/0.3/0.12 Minimum switching load mW (V/mA) 300 (5/5) 300 (5/5) Standard contact material AgNi AgNi Coil specification Nominal voltage (U ) VAC (50/60Hz) 12 - 24 - 110 - 120 - 230 12 - 24 - 110 - 120 - 230 N VDC 12 - 24 - 125 12 - 24 - 125 Rated power AC/sens. DC VA (50Hz)/W 1.2/0.5 1.2/0.5 Operating range AC (0.81.1)U (0.81.1)U N N sens. DC (0.731.5)U (0.731.5)U N N Holding voltage AC/DC 0.8U /0.4U 0.8U /0.4U N N N N Must drop-out voltage AC/DC 0.2U /0.1U 0.2U /0.1U N N N N Technical data 6 6 Mechanical life cycles 1010 1010 3 3 Electrical life at rated load AC1 cycles 20010 20010 Operate/release time ms 7/4 (AC) - 12/12 (DC) 7/4 (AC) - 12/12 (DC) Insulation between coil and contacts (1.2/50s) kV 6 (8mm) 6 (8mm) Dielectric strength between open contacts VAC 1000 1000 Ambient temperature range C 40+70 40+70 Protection category IP 20 IP 20 Approvals relay (according to type) 2 X-2016, www.findernet.com