FTLF8524P2BNV Finisar

Product Specification 4.25 Gb/s RoHS Compliant Short-Wavelength SFP Transceiver FTLF8524P2xNy PRODUCT FEATURES Up to 4.25 Gb/s bi-directional data links Hot-pluggable SFP footprint Built-in digital diagnostic functions 850nm Oxide VCSEL laser transmitter Duplex LC connector APPLICATIONS RoHS Compliant and Lead Free Up to 500m on 50/125m MMF, Tri-Rate 1.063/2.125/4.25 Gb/s 300m on 62.5/125m MMF Fibre Channel Metal enclosure, for lower EMI 1.25 Gb/s 1000Base-SX Ethernet Single 3.3V power supply (Rate selectable version) Extended operating temperature Wireless OBSAI, CPRI range: -20C to 85C Finisars FTLF8524P2xNy Small Form Factor Pluggable (SFP) transceivers are 1 compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA) . 2 They are compatible with Fibre Channel FC-PI-2 Rev. 7.0 . Rate Selectable versions are 3 also compatible with Gigabit Ethernet as specified in IEEE Std 802.3 . The optical transceivers are compliant per the RoHS Directive 2011/65/EU. See Finisar Application Note AN-2038 for more details. Digital diagnostics functions are available via the 2-wire serial bus specified in the SFP MSA. PRODUCT SELECTION FTLF8524P2xNy x W Wide Extraction Bail B Narrow Extraction Bail L Non Rate Selectable - 1x, 2x, 4x Fibre Channel y V Rate Selectable - 1x, 2x, 4x Fibre Channel and Gigabit Ethernet Finisar Corporation August 2015 Rev.K Page 1 FTLF8524P2xNy Pluggable SFP Product Specification I. Pin Descriptions Pin Symbol Name/Description Ref. 1 V Transmitter Ground (Common with Receiver Ground) 1 EET 2 T Transmitter Fault. FAULT 3 T Transmitter Disable. Laser output disabled on high or open. 2 DIS 4 MOD DEF(2) Module Definition 2. Data line for Serial ID. 3 5 MOD DEF(1) Module Definition 1. Clock line for Serial ID. 3 6 MOD DEF(0) Module Definition 0. Grounded within the module. 3 7 Rate Select Open or Low = 1.063 Gb/s or 2.125 Gb/s Fibre Channel, 1.25 Gb/s 4 Gigabit Ethernet (Low Bandwidth) High = 2.125 or 4.25 Gb/s Fibre Channel (High Bandwidth) 8 LOS Loss of Signal indication. Logic 0 indicates normal operation. 5 9 V Receiver Ground (Common with Transmitter Ground) 1 EER 10 V Receiver Ground (Common with Transmitter Ground) 1 EER 11 V Receiver Ground (Common with Transmitter Ground) 1 EER 12 RD- Receiver Inverted DATA out. AC Coupled 13 RD+ Receiver Non-inverted DATA out. AC Coupled 14 V Receiver Ground (Common with Transmitter Ground) 1 EER 15 V Receiver Power Supply CCR 16 V Transmitter Power Supply CCT 17 V Transmitter Ground (Common with Receiver Ground) 1 EET 18 TD+ Transmitter Non-Inverted DATA in. AC Coupled. 19 TD- Transmitter Inverted DATA in. AC Coupled. 20 V Transmitter Ground (Common with Receiver Ground) 1 EET Notes: 1. Circuit ground is internally isolated from chassis ground. 2. Laser output disabled on T >2.0V or open, enabled on T <0.8V. DIS DIS 3. Should be pulled up with 4.7k 10kohms on host board to a voltage between 2.0V and 3.6V. MOD DEF(0) pulls line low to indicate module is plugged in. 4. For Rate Selectable version only: In accordance with SFF Committee SFF-8079 Draft Rev. 1.6, 5 Table 3. Note that rate select can also be set through 2-wire bus in accordance with SFF-8472 at Bit 3, Byte 110, Address A2h (note: writing 1 selects full bandwidth operation). Rate select is the logic OR of the input state of Rate Select Pin and 2-wire bus. Non Rate Selectable version can operate at 1x, 2x, 4x Fibre Channel independent of rate select pin setting. 5. LOS is open collector output. Should be pulled up with 4.7k 10kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation logic 1 indicates loss of signal. VeeT 20 1 VeeT TD- 19 2 TXFault TD+ 18 3 TX Disable VeeT 17 4 MOD-DEF(2) VccT 16 5 MOD-DEF(1) Towards Towards VccR 15 Bezel MOD-DEF(0) 6 ASIC VeeR 14 7 Rate Select RD+ 13 8 LOS RD- 12 9 VeeR VeeR 11 10 VeeR Diagram of Host Board Connector Block Pin Numbers and Names Finisar Corporation August 2015 Rev.K Page 2