FTLX2672D327 Finisar

Product Specification RoHS-6 Compliant 10Gb/s 30km Single Mode Bidirectional SFP+ Transceiver FTLX2672D327/FTLX2672D333 PRODUCT FEATURES Hot-pluggable SFP+ footprint Bidirectional 10G over single strand single mode fiber Supports 1.0 to 11.3Gb/s bit rates Power dissipation <1W RoHS-6 compliant (lead-free) Industrial temperature range -40C to 85C APPLICATIONS 10GBASE-LR/LW 10G Ethernet Single 3.3V power supply 1000BASE-LX10 Gigabit Ethernet Maximum link length of 30km 1200-SM-LL-L 10G Fibre Channel Uncooled DFB 2.457 Gb/s CPRI Receiver limiting electrical 3.072 Gb/s CPRI/LTE interface 4.915 Gb/s CPRI/LTE 6.144 Gb/s CPRI/OBSAI/LTE Single LC connector 9.8304 Gb/s CPRI/LTE Built-in digital diagnostic functions Finisars FTLX2672D327/FTLX2672D333 10Gb/s Enhanced Small Form Factor Pluggable SFP+ transceivers are designed for use in 10-Gigabit Ethernet links up to 30km over a single- strand Single Mode fiber. This capability doubles the capacity of installed legacy single mode 1 3 fiber links. They are compliant with SFF-8431 and IEEE 802.3ae 10GBASE-LR/LW , and 4 10G Fibre Channel 1200-SM-LL-L . Digital diagnostics functions are available via a 2-wire 5 serial interface, as specified in SFF-8472 . The FTLX2672D327/FTLX2672D333 is a limiting module, i.e., it employs a limiting receiver. Host board designers using an EDC PHY IC should follow the IC manufacturers recommended settings for interoperating the host-board EDC PHY with a limiting receiver SFP+ module. The optical transceiver is 6 7 compliant per the RoHS Directive 2011/65/EU . See Finisar Application Note AN-2038 . PRODUCT SELECTION Part Number Wavelength FTLX2672D327 1271 nm FTLX2672D333 1331 nm Finisar Corporation August 2016 Rev A4 Page 1 FTLX2672D3xx Product Specification I. Pin Descriptions Pin Symbol Name/Description Ref. 1 V Transmitter Ground 1 EET 2 T Transmitter Fault 2 FAULT 3 T Transmitter Disable. Laser output disabled on high or open. 3 DIS 4 SDA 2-wire Serial Interface Data Line 2 5 SCL 2-wire Serial Interface Clock Line 2 6 MOD_ABS Module Absent. Grounded within the module 2 7 RS0 Rate Select 0. Not Used. 4 8 RX_LOS Loss of Signal indication. Logic 0 indicates normal operation. 5 9 RS1 Rate Select 1. Not Used. 4 10 V Receiver Ground 1 EER 11 V Receiver Ground 1 EER 12 RD- Receiver Inverted DATA out. AC Coupled. 13 RD+ Receiver Non-inverted DATA out. AC Coupled. 14 V Receiver Ground 1 EER 15 V Receiver Power Supply CCR 16 V Transmitter Power Supply CCT 17 V Transmitter Ground 1 EET 18 TD+ Transmitter Non-Inverted DATA in. AC Coupled. 19 TD- Transmitter Inverted DATA in. AC Coupled. 20 V Transmitter Ground 1 EET Notes: 1. Circuit ground is internally isolated from chassis ground. 2. T is an open collector/drain output, which should be pulled up with a 4.7k 10k Ohms resistor on FAULT the host board if intended for use. Pull up voltage should be between 2.0V to Vcc + 0.3V. A high output indicates a transmitter fault caused by either the TX bias current or the TX output power exceeding the preset alarm thresholds. A low output indicates normal operation. In the low state, the output is pulled to <0.8V. 3. Laser output disabled on T >2.0V or open, enabled on T <0.8V. DIS DIS 4. Internally pulled down per SFF-8431 Rev 4.1. 5. LOS is open collector output. Should be pulled up with 4.7k 10k on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. VeeT 20 1 VeeT TD- 19 2 TX_Fault TD+ 18 3 TX_Disable VeeT 17 4 SDA VccT 16 5 SCL Towards Towards VccR 15 6 MOD_ABS Bezel ASIC VeeR 14 7 RS0 RD+ 13 8 RX_LOS RD- 12 9 RS1 VeeR 11 10 VeeR Figure 1. Diagram of Host Board Connector Block Pin Numbers and Names. Finisar Corporation August 2016 Rev A4 Page 2