FT905/6/7/8 Embedded Microcontroller Datasheet Version 1.2 Document No.: BRT 000023 Clearance No.: BRT 026 Future Technology Devices International Ltd. FT905/6/7/8 (Embedded Microcontroller) The FT90x series includes the FT905, FT906, FT907 Two CAN controllers support CAN protocol2.0 and FT908 which are complete System-On-Chip parts A&B, data rate is up to 1Mbit/s. (FT905 32-bit RISC microcontrollers for embedded and FT907 only). applications featuring a high level of integration One SPI master supports single / dual / quad and low power consumption. They have the modes of data transfer. Clock rate is up to 25 following features: MHz. High performance, low power 32-bit FT32core One SPI slave supports single data transfer processor, running at a frequency of 100MHz. with a 25MHz clock. 256kB on-chip Flash memory. 2 One I C bus interface can be configured as 256kB on-chip shadow program memory. master or slave, which support standard / fast / fast plus / high speed mode data transfers. True Zero Wait States (0WS) up to 3.1 DMIPS Max data transfer rate up to 3.4Mbit/s. Clock per MHz performance. stretching is supported. 64kB on-chip data memory. UART interface can be configured as one full programmable UART0 or two simple UART0 and EFUSE for security configuration. UART1 with CTS / RTS control function only. Integrated Phase-Locked Loop (PLL) supports Four user timers with pre-scaling and a external 12MHz crystal and direct external watchdog function. clock source input. Support 7 independent PWM channels. Channel 32.768 kHz real time clock support. 0 and 1 can be configured as PCM 8-bit/16-bit One USB2.0 EHCI compatible host controller stereo audio output. supports high-speed (480Mbit/s), full-speed Support two 10-bit DACs 0/1 channels output, (12Mbit/s), and low-speed (1.5Mbit/s). sample rate at ~1 MS/s. One USB2.0 peripheral controller supports Support four 10-bit ADC 1/4 channels input, high-speed (480Mbit/s) and full-speed sample rate is up to ~960 KS/s. (12Mbit/s). Single 3.3 volt power supply, built-in 1.2 V USB2.0 host and peripheral controllers support regulators. the Isochronous, Interrupt, Control, and Bulk transfers. 3.3 volt I/O power supply. Supports USB Battery Charging Specification Support VBUS power switching and overcurrent Rev 1.2. Downstream port can be configured as control. SDP, CDP or DCP. Upstream port can perform BCD mode detection. Provides a Power-On Reset (POR) signal to indicate stable power regulator. 10/100Mbps Ethernet that is compliant with the IEEE 802.3/802.3u standards. (FT905 and -40C to 85C extended operating temperature FT906 only). range. Supports One-Wire debugger for downloading Available in compact Pb-free -76-pin (QFN) and firmware to Flash memory or shadow program 80-pin (LQFP) packages (all RoHS compliant). memory, and supports a software debugger. Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH United Kingdom. Scotland Registered Company Number: SC136640 Copyright Bridgetek Limited 1 FT905/6/7/8 Embedded Microcontroller Datasheet Version 1.2 Document No.: BRT 000023 Clearance No.: BRT 026 1 Typical Applications Home security system CCTV monitor Home Automation Industrial automation Embedded audio application Medical appliances Motor drive and application control Instrumentation E-meter DAQ System 1.1 Part Numbers Part Number Package 76 Pin QFN, pitch 0.4mm, body 9mm x 9mm x 0.9mm, support both CAN Bus FT905Q-X and Ethernet features. 80 Pin LQFP, pitch 0.4mm, body 10mm x 10mm x 1.40mm, support both CAN FT905L-X Bus and Ethernet features. 76 Pin QFN, pitch 0.4mm, body 9mm x 9mm x 0.9mm, support Ethernet, FT906Q-X doesnt support CAN Bus. 80 Pin LQFP, pitch 0.4mm, body 10mm x 10mm x 1.40mm, support Ethernet, FT906L-X doesnt support CAN Bus. 76 Pin QFN, pitch 0.4mm, body 9mm x 9mm x 0.9mm, support CAN Bus, FT907Q-X doesnt support Ethernet. 80 Pin LQFP, pitch 0.4mm, body 10mm x 10mm x 1.40mm, support CAN Bus, FT907L-X doesnt support Ethernet. 76 Pin QFN, pitch 0.4mm, body 9mm x 9mm x 0.9mm, doesnt support either FT908Q-X CAN Bus or Ethernet features. 80 Pin LQFP, pitch 0.4mm, body 10mm x 10mm x 1.40mm, doesnt support FT908L-X either CAN Bus or Ethernet features. Table 1-1 FT90x series Part Numbers Note: Packaging codes for x is: -R: Taped and Reel (qty per reel for LQFP is 1000 qty per reel for QFN is 3000) -T: Tray packing (qty per tray for LQFP is 160 qty per tray for QFN is 260) 1.2 USB2.0 Compliant The FT90x series contains a USB2.0 host controller and peripheral controller that are both compliant with USB2.0 specification. Copyright Bridgetek Limited 2