UMFTPD2A PROGRAM MODULE Version 1.3 Document No.: BRT 000027 Clearance No.: BRT 029 Future Technology Devices International UMFTPD2A UMFTPD2A is a module used for FT90x programming, debugging and EFUSE burning. The UMFTPD2A is a module with an FT4232HL The UMFTPD2A has the following features: Hi-Speed USB2.0 to multipurpose UART/MPSSE converter. The UMFTPD2A module features a Hi-Speed USB to one-wire interface converter single line half-duplex UART signal with no Hi-Speed USB to MPSSE interface converter handshake (One-Wire interface), one MPSSE interface, one UART interface and a Bit-Bang Hi-Speed USB to UART interface converter port. Provides H/W Reset signal The module has configured the FT4232HL Channel A as a UMFTPD2A one-wire interface Provide multiple generic GPIO control signals for MM900EVxA evaluation board firmware / application download, or GDB debugging. PWREN line to control +5V power supply The FT4232HL Channel B is configured as a Fuse protected with 0.5A hold current and schottky UMFTPD2A MPSSE interface with 4 GPIO control diode on the output power line. signals. This allows the UMFTPD2A to implement MM900EVxA evaluation board EFUSE program, Two dedicated GPIOs to control VPP and FRSC or firmware / application upload as well. power supplies The FT4232HL Channel C is optional. It is Three LEDs for power supply indication configured as a UART that can capture the messages from MM900EVxA evaluation board in 2X5 way 1.27mm pitch Micro-MaTch socket software debugging. 2X6 way 2.54mm pitch through hole pin header The FT4232HL Channel D is reserved as a Bit- Bang interface for generic GPIO purposes. Mirco-B type USB port The FT90x program utility can activate the Micro-MaTch Male to Male 10 pin ribbon cable required channels corresponding to the operations. All components used are Pb-free (RoHS compliant) Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Future Technology Devices International Ltd, Unit1, 2 Seaward Place, Centurion Business Park, Glasgow, G41 1HH, United Kingdom. Scotland Registered Number: SC136640 Copyright Bridgetek Limited 1 UMFTPD2A PROGRAM MODULE Version 1.3 Document No.: BRT 000027 Clearance No.: BRT 029 Table of Contents 1 Driver Support ................................................................ 3 2 Programming Utility Support........................................... 3 3 Ordering Information ...................................................... 3 4 UMFTPD2A Signals .......................................................... 4 4.1 UMFTPD2A Pin Out .................................................................... 4 4.2 Signal Descriptions ................................................................... 5 5 Module Dimensions ......................................................... 7 6 UMFTPD2A Module Circuit Schematic .............................. 8 7 Hardware Setup Guide .................................................. 10 7.1 Module Connect to PC ............................................................. 10 7.2 Module Connect to MM900EVx ................................................ 10 7.3 FT900 Programming Utility ..................................................... 10 8 Contact Information ...................................................... 12 Appendix A References ................................................... 11 Document References ..................................................................... 11 Acronyms and Abbreviations ........................................................... 11 Appendix B List of Figures and Tables ............................. 12 List of Figures ................................................................................. 12 List of Tables ................................................................................... 12 Appendix C Revision History ........................................... 13 Copyright Bridgetek Limited 2