DF81D-40P-0.4SD(52) Hirose

0.4 mm Pitch, Horizontal Mating, Board-to-Micro-Coaxial Cable Connector DF81 Series Enhanced shielding capability Grounding connection between plug connector and receptacle connector 30 contacts: 5 locations / 40 contacts: 7 locations / 50 contacts: 9 locations <gdjcY c XdccZXi dc Grounding connection between receptacle connector and PCB 30 contacts: 10 locations / 40 contacts: 12 locations / 50 contacts: 14 locations Features <gdjcY c XdccZXi dc 1. Space saving design Utilizing its 0.4 mm pitch, this horizontal connector <gdjcY c offers a space saving design and a low height of 0.9 XdccZXi dc mm in a single row connector. 2. High speed transmissions Designed to optimize transmission speeds, the DF81 Fig.1 series provides superior signal characteristics. TM TM eDP Embedded DisplayPort Ver. 1.3 compatible Positive lock by using the latch 5.4 Gbps Unlocking is possible by rotating the latch. MIPI (D-PHY) 3.Enhanced shielding Shielding capacity has increased by providing multiple grounding points (Fig.1). 4. Positive locking structure The positive locking structure utilizes a rotary latch that prevents incomplete mating. (Fig.2) 5. Excellent mating operation Fig.2 Excellent self-alignment allows for easier mating. (Fig.3) 6. Accepts both micro coaxial cable and Excellent mating operability discrete wire Wide self-alignment (X direction: 0.45, Z direction: 0.15) Its versatility allows micro coaxial cable and discrete wire to be used together on a single connector. 7. Solder wicking prevention % &*bb % )*bb Nickel barriers are strategically placed between the receptacles contact area and the soldered lead area to prevent solder wicking. 8. RoHS compliant, Halogen-free O Chlorine and bromine are not used in these connectors and do not exceed standard values. N * It is defined according to IEC 61249-2-21. Br: 900 ppm or less, Cl: 900 ppm or less, Br + Cl: M 1,500 ppm or less Fig.3 In cases where the application will demand a high level of reliability, such as automotive, 1 2014.6w please contact a company representative for further information.DF81 series0.4 mm Pitch, Horizontal Mating, Board-to-Micro-Coaxial Cable Connector Product specifications Discrete wire AWG 34: 0.3 A(MAX0.8 A) AWG 36: 0.3 A(MAX0.8 A) Micro coaxial cable Rated Operating Temperature Range -35 to 85(Note 1) (Note 3) AWG 36: 0.3 A(MAX0.8 A) Current (Note 4) Operating Humidity Range 20 to 80 AWG 40: 0.25 A Ratings AWG 42: 0.2 A AWG 44: 0.15 A AWG 46: 0.1 A Rated Storage Temperature Range -10 to 60 (Note 2) 100 V AC/DC Voltage Storage Humidity Range 40 to 70(Note 2) Items Speci cations Conditions 1. Insulation Resistance 50 M or greater Measured at 100 V DC 2. Withstanding Voltage No ashover or breakdown Conduct 250 V AC for one minute Signal: 80 m or lower 3. Contact Resistance Measured at 100 mA (DC or 1,000 Hz) GND: 80 m or lower 10 cycles in each of three directions at frequency 10- 4. Vibration Resistance No electric outage of 1s or greater 55 Hz, single amplitude 0.75 mm Contact resistance (amount of change Temperature: 40 2C, 5. Moisture Resistance from the initial state): 50 m or lower Humidity: 90 to 95%, Insulation resistance: 25 M or greater Leave 96 hours Contact resistance (amount of change (-55C: 30 minutes 5 to 35C: 2 to 3 minutes 6. Temperature Cycles from the initial state): 50 m or lower 85C: 30 minutes 5 to 35C: 2 to 3 minutes) Insulation resistance: 25 M or greater 5 cycles Contact resistance (amount of change 7. Mating Cycles 30 cycles from the initial state): 50 m or lower 8. Solder Heat There should be no dissolution of the resin Re ow: According to the Recommended Temperature Pro le Resistance part which will in uence the performance. Hand soldering: Soldering iron temperature of 350C for 3 seconds (Note 1) Temperature rise at the time of electri cation is included. (Note 2) The term storage refers to the long-term storage of unused products in its original packaging before PCB mounting. Operating Temperature/Humidity Ranges are applied to the deenergized state after mounting of PCB and the temporary storage state during transportation. (Note 3) Current will vary depending on use conditions.MA is rating current as only two of them turn on electricity. (Note 4) Rated current value is set only using the temperature rise value of the connector. Materials Product Parts Materials Treatment UL Recognition Insulator LCP Black UL94V-0 Receptacle Contact Phosphor bronze Gold plating ------------- Metal fitting Stainless steel Partially gold plated ------------- Insulator LCP Black UL94V-0 Plug Contact Phosphor bronze Gold plating ------------- Outer shell Stainless steel Partially gold plated ------------- Shell Outer shell Stainless steel Partially gold plated ------------- Latch Locking bar Stainless steel / polyester ------------- ------------- Product Number Structure Refer to the chart below when searching for the part number nomenclature. Series Name: DF Please make a selection from the connectors listed on pages 3 to 6 of Series No.: 81/81D this catalog when placing orders. Numbers of Contacts: 30, 40, 50 Connector type S: Receptacle P: Plug Connector Contact pitch: 0.4mm Termination Type DF 81 * S 0.4 H (* *) H: Right Angle SMT SD: Solder wire termination Packaging Type DF 81 * P SHL (51): Embossed packaging Parts for Assembly SHL: Outer shell LCH: Latch 2