16.9mm NEW 0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors FH36 Series Space saving (51 positions shown) 2.7mm 51 Positions Features Metal fittings do not protrude outside of the connector body 1. Low-profile and light weight Can be mounted over conductive traces Weight: Reduced approximately 30% Board footprint: Reduced approximately 15% (As compared with Hirose Electric s FH26 Series connectors (51 positions) 2. Easy solderability on the PC board The soldering leads are on 0.6 mm pitch, exiting on front and No exposed contacts on the bottom of back of the connector. the connector 3. Conducive traces on the PCB can run under Operation the connector (1) Actuator open(1) Actuator open No exposed contacts on the bottom of the connector. (2) Insert FPC(2) Insert FPC ActuatorActuator 1 4. Easy FPC insertion and reliable electrical connection Proven Flip Lock actuator allows easy insertion of FPC and provides a tactile sensation when fully closed, confirming 2 complete electrical and mechanical connection. FPCFPC 5. FPC position hold Tabs on each side of the FPC assure correct placement and hold in the connector prior to closing of the actuator. (3) Close the actuator(3) Close the actuator(3) Close the actuator (4) FPC connected(4) FPC connected 6. Accepts standard FPC thickness 3 0.2mm thick standard Flexible Printed Circuit (FPC) can be used. This is the only ultra-low profile ZIF connector using standard FPC. 7. Board placement with automatic equipment 4 Flat upper surface and tape and reel packaging facilitate vacuum pick-up and placement. Standard reel packaging contains 5,000 connectors. * FPC temporary hold 8. Halogen-free (FH36W Series) *As defined by IEC61249-2-21 Br-900ppm maximum, Cl-900ppm maximum, Cl + Br combined-1,500ppm maximum 2010.9 1 1.0mm MAX FH36 Series 0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors Specifications Operating Storage Current rating 0.2 A DC (Note 1) -55 to +85C (Note 2) -10 to +50C (Note 3) temperature range temperature range Rating Operating Relative humidity 90% Storage Relative humidity 90% Voltage rating 30 Vrms AC humidity range max. (No condensation) humidity range max. (No condensation) Recommended FPC Thickness: 0.20.03mm Gold plated Item Specification Conditions 100 V DC 1.Insulation resistance 50 M min 90 Vrms AC / one minute 2.Withstanding voltage No flashover or insulation breakdown 100 m max. 3.Contact resistance 1 mA * Including FPC conductor resistance Contact resistance: 100 m max. 4.Durability 10 cycles No damage, cracks, or parts dislocation No electrical discontinuity of 1 s or longer Frequency: 10 to 55 Hz, single amplitude of 0.75 mm 5.Vibration Contact resistance: 100 m max. 10 cycles in each of the 3 directions No damage, cracks, or parts dislocation No electrical discontinuity of 1 s or longer 2 Acceleration of 981m/s , 6 ms duration, 6.Shock Contact resistance: 100 m max. sine half-wave, 3 cycles in each of the 3 axis No damage, cracks, or parts dislocation Contact resistance: 100 m max. 7.Humidity 96 hours at a temperature of 40C and humidity of Insulation resistance: 50 M min. (Steady state) 90 to 95% No damage, cracks, or parts dislocation Contact resistance: 100 m max. Temperature:-55+15 to +35 +85 +15 to +35 8.Temperature cycle Insulation resistance: 50 M min. Time: 30 2 to 3 30 2 to 3 minutes No damage, cracks, or parts dislocation 5 cycles 9.Resistance to 1) Reflow: At the recommended temperature profile. No deformation of components affection performance. soldering heat 2) Manual soldering: 350 10 for 5 seconds Note 1: When passing the current through all of the contacts, use 70% of the rated current. Note 2: Includes temperature rise caused by current flow. Note 3: The termstorag refers to products stored for a long period prior to mounting and use. The operating temperature and humidity range covers the non-conducting condition of installed connectors in storage, shipment or during transportation. Note 4: Small blisters of the molding compounds in small areas will not affect form, fit or function. Note 5: Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and specifications for a specific part number shown. Materials Part Material Finish Remarks Insulator LCP Color: Beige UL94V-0 FH36 series: Dark brown Actuator PA FH36W series: Light brown UL94HB Contacts Gold plating ----------------- Phosphor bronze Metal fittings Pure tin reflow plating ----------------- Or dering information FH 36 W - 51S - 0.3 SHW (50) 1 2 3 4 5 6 7 1 Series name : FH 4 Number of positions : 11 to 61 2 Series No. : 36 5 Contact pitch : 0.3mm 3 Blank :Standard 6 Termination type: SMT horizontal staggered mounting type W :Halogen-free 7 Plating specifications (50)Gold plating with nickel barrier (Flame retardance UL94HB). 2