Signal contact
0.5mm pitch
Ground contact
2.5mm pitch
0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
FH41 Series
THine Electronics, Inc.
Next-generation chipset (V-by-One HS*)
Compatible connector
=^\heZZYhZg^Va^ciZg[VXZiZX]cdad\n
[dg^bV\ZigVchb^hh^dc
Space saving (68 pos. shown)
'#*bb
(-bb
Features
1. Compatibility with impedance control, shield
FFC
The FH41 series is equipped with a GND exclusive terminal
+#'bb
and available for connection with impedance control, shield
FFC.
figure.1
2.Differential impedance 100 10%
The FH41 series features a terminal design considering
impedance control, and making high speed transmission
possible.
3.Highly reliable connection, tough structure
The FH41 series follows the structure of the proven FH28
series, and achieves:
- High reliability thanks to the FFC positioning mechanism
- Reliable connection operation and no unlocking thanks to the
durable structure.
4.One-finger operation of the actuator
Proven (in several other Hirose's connectors!) Flip-Lock
rotating actuator assures reliable mechanical and electrical
connection with FPC, confirming it with a definite tactile feel.
figure.2
5.Board placement with automatic equipment
Flat upper surface and tape and reel packaging facilitate
H^\cVa XdciVXi XdccZXi^dcVgZV
vacuum pick-up and placement.
Standard reel packaging contains 2,500 connectors.
*
6.Halogen-free
*As defined by IEC61249-2-21
Br-900ppm maximum, Cl-900ppm maximum,
Cl + Br combined-1,500ppm maximum
<C9XdciVXiXdccZXi^dcVgZV
figure.3
2010.9
1FH41 Series0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
Specifications
O perating temperature range: S torage temperature range:
Current rating 0.5 A(Note1) -40 to +85C (Note 2) -10 to +50C (Note 3)
Ratings
Voltage rating 50 Vrms AC O perating humidity range: S torage humidity range:
Relative humidity 90% max. (No condensation) Relative humidity 90% max. (No condensation)
Recommended FPC Thickness 0.3 0.05 mm, Gold plated contact pads (GND plate:t=0.50.05mm,tinplateing)
Item Speci cation Conditions
1. Insulation
500 M min. 100 V DC
resistance
2.Withstanding voltage No ashover or insulation breakdown
150 Vrms AC / one minute
100 m max.
3.Contact resistance 1 mA, AC max (AC: 1kHz)
* Including FFC conductor resistance
Contact resistance: 100 m max.
4.Durability
20 cycles
No damage, cracks, or parts dislocation
No electrical discontinuity of 1s or longer
Frequency: 10 to 55 Hz, single amplitude of 0.75mm,
5.Vibration Contact resistance: 100 m max.
10 cycles in each of the 3 directions
No damage, cracks, or parts dislocation
No electrical discontinuity of 1s or longer
2
Acceleration of 981m/s 6 ms duration, sine halfwave,
6.Shock
Contact resistance: 100 m max.
3 cycles in each of the 3 axis
No damage, cracks, or parts dislocation
Contact resistance: 100 m max.
7.Humidity
Insulation resistance: 50 M min. 96 hours at 40C and humidity of 90 to 95%
(Steady state)
No damage, cracks, or parts dislocation
Temperature : -40C +15C to +35C +85C
Contact resistance: 100 m max.
+15C to +35C
8.Temperature cycle Insulation resistance: 50 M min.
Time: 30 2 to 3 30 2 to 3 minutes
No damage, cracks, or parts dislocation
5 cycles
9. Resistance to Re ow: At the recommended temperature pro le
No deformation of components affecting performance
soldering heat Manual soldering: 350C 5C for 5 seconds
Note 1. When passing the current through all of the contacts, use 70% of the rated current.
Note 2. Includes temperature rise caused by current ow.
Note 3. The termstorag refers to products stored for a long period prior to mounting and use.
The operating temperature and humidity range covers the non-conducting condition of installed connectors in storage, shipment or
during transportation after board mounting.
Note 4. Information contained in this catalog represents general requirements for this Series.
Contact us for the drawings and speci cations for a speci c part number shown.
Materials
Part Material Finish Remarks
Color:Gray
Insulator LCP UL94V-0
Color:Black
Gold plated
Contacts Phosphor bronze
---------
Pure tin re ow plated
Metal ttings Brass
Ordering information
( )
FH 41 50S 0.5 SH 05
Series name : FH SH : SMT horizontal mounting type
Series No.: 41
Plating speci cations :(05)Gold plated
Number of positions : 28 to 68
Contact pitch : 0.5mm
2