Lightweight SMT Miniature Coaxial Connectors 1.4 mm Mated Height N.FL Series Mated height comparison (With U.FL-LP(V) ) N.FL U.FL-LP(V) Fig.1 N.FL Plug and Receptacle Features 1. Low profile Nominal mated height is 1.4 mm (Max. 1.5 mm) 2 N.FL-LP-040* 2. Small size: 7.7 mm Plug 3. Light weight 3.4 Cable Receptacle : 14 mg Plug : 28 mg 4. Accepts high frequency transmission of DC to 6 GHz. V.S.W.R. = 1.3 max. (DC to 6 GHz) 5. Board placement with automatic equipment N.FL-R-SMT-1 Receptacles are packaged in embossed carrier Receptacle tape and reel for automatic mounting. Fig.2 6. Plugs are terminated with ultra-fine coaxial (fluorinated resin insulated) cable. 7. Special tool for an extraction 8. Verification of the fully mated condition Tactile click sensation confirms fully mated condition, assuring complete electrical and mechanical connection 9. Halogen-free*(Receptacle, plug(HF type)) *As defined by IEC61249-2-21 Br-900 ppm maximum, Cl-900 ppm maximum, Cl+Br combined - 1,500 ppm maximum Applications Mobile phones, wireless communication devices, electronic measuring instruments, GPS, wireless LAN, Bluetooth and any application requiring high frequency transmission using small coaxial connectors. In cases where the application will demand a high level of reliability, such as automotive, 1 2014.10w please contact a company representative for further information. 1.4(1.5MAX) 1.4(1.5MAX) 1.9(2.0MAX) Dia.0.81N.FL SeriesLightweight SMT Miniature Coaxial Connectors 1.4 mm Mated Height Specifications -40C to +90C Nominal characteristic impedance 50 ohms Operating temperature range (90% RH max.) Ratings -30C to +70C Frequency range DC to 6 GHz Storage temperature range (90% RH max.) Item Specification Conditions Center contact: 25 m ohms max. 1. Contact resistance 10 mA max. Outer contact: 25 m ohms max. 2. Insulation resistance 500 M ohms min. 100V DC 3. Withstanding voltage No flashover or insulation breakdown 200V AC / 1 minute 4. V.S.W.R.(Note) 1.3max. DC to 6GHz Contact resistance Center contact: 30 m ohms max. 5. Durability Outer contact: 30 m ohms max. 20 cycles No damage, cracks, or parts dislocation Frequency: 10 to 100 Hz, single amplitude of 1.5 mm No electrical discontinuity of 1 s or longer 2 6. Vibration Acceleration: 59 m/s , in each of 3 axis No damage, cracks, or parts dislocation 5 cycles 2 No electrical discontinuity of 1 s or longer Acceleration of 735 m/s , 11 ms continuous time 7. Shock No damage, cracks, or parts dislocation Waveform: sine half-wave, 3 cycles in each of the 3 axis Insulation resistance: 100 M ohms min. (high humidity) 8. Humidity Insulation resistance: 500 M ohms min. (dry) 96 hours at +40C, and humidity of 95% No damage, cracks, or parts dislocation Temperature:-40C/+5C to +35C/+90C/+5C to +35C 9. Temperature cycle No damage, cracks, or parts dislocation Time: 30 min./ 5 min. max. / 30 min. / 5 min. max. 5 cycles 10. Salt spray test No excessive corrosion 5% salt water solution, 48 hours Note: Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and specifications for a specific part number shown. * V.S.W.R. Measurement System Measured as shown on the block diagram below. Note1: N.FL Cable assembly (plug) is measured with SMA conversion Network Analyzer adapters mated with N.FL plugs at both ends of a 100cm coaxial Test Set cable harness Test Port Note2: N.FL receptacle, which is mounted on a 50 ohms glass epoxy D.U.T Termination board, is measured with a SMA conversion adapter. Test Port Cable Materials / Finishes Plugs-Right Angle Part Material Finish Shell Phosphor bronze Silver plated Female center contact Phosphor bronze Gold plated Color: Black, UL94V-0 Insulator PBT Color: Gray, UL94HB(HF type) Receptacle Part Material Finish Shell Phosphor bronze Silver plated Male center contact Brass Gold plated Insulator LCP Color: Black, UL94V-0 2