The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. Meet requirements of USB 2.0 UX Series Features 1. Certified to perform as required in USB 2.0 Standard Tested and certified by USB Association approved laboratory the connectors will perform at transmission speeds up to 480Mbps. 2. Designed for Low Skew performance The distance between twisted pairs conductors (i.e., contact nos. 2 and 3) is of equal electrical length, for receptacle and plug, resulting in zero theoretical skew. 3. Controlled Termination of Individual Conductors The termination part of the contact is firmly attached in the molded insulator body. Hiroses Electric unique design of the metal shield prevents short circuits, allowing the overmold resin to flow in the terminated area. By not using heat shrinkable tubing (or any other additional process), Contact No. 3 the non-twisted part of the conductors is very short, suppressing any Contact No. 2 unwanted impedance disturbances in the termination area. 4. Ease of mating and handling Thin design of the plug assembly and the overmold section allows use in small spaces. The plug also incorporates a build-in snap-lock feature, providing tactile verification of the full and secure mating of plug and receptacle. 5. Two types of metal shields Two styles of the receptacle metal shield are available, depending on the customers PCB design requirement: -Surface Mount Termination -Solder Dip Type 6. Printed Circuit Board placement features Precise location on the board can be accomplished using receptacle assemblies with or without the positioning boss. 7. Board placement with Automatic Equipment Receptacle assemblies are provided with a heat resistant flat surfaces, removable after completion of the soldering process and are supplied on the reels. 8. RoHS Compliant All components and materials comply with the requirements of the EU Directive 2002/95/EC. 9. Support of Non-halogen Cable Wiring harness can be arranged in non-halogen cable types. Note: Non-halogen items are not covered in the current USB 2.0 Standard. Applications Personal and mobile computer peripheral equipment, data terminals, digital cameras, MP3 players, PDAs, GPS and other devices utilizing standard USB protocols 2008.4w 1The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. UX SeriesMeet requirements of USB 2.0 Product Specifications Current rating 1 A Ratings Operating temperature range + (Note 1) -30 to 75 Voltage rating 5 V AC Item Specification Conditions Measured at 100 mA 1.Contact resistance 50 m ohms max. 2.Insulation resistance 100 M ohms min. Measured at 100 V DC 3.Dielectric No flashover or insulation breakdown 100 V AC / one minute Withstanding Voltage 4.Capacitance 2 pF min. Measured at 1000 10Hz between adjacent contacts Mating : 35N max. With corresponding connector. 5.Mating/un-mating forces Un-mating : 7N min. 6.Durability Contact resistance: 70 m ohms max. 5000 cycles (mating / un-mating) Un-mating force: 3N min. Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 7.Vibration 2 hours in each of the 3 axis. Frequency: 50 to 2000 Hz, 15 minutes in each of the 3 axis. 8.Shock No electrical discontinuity of 1 ms or more. 2 Acceleration of 490 m/s , 11 ms duration, sine half-wave 9.Shock waveform, 3 cycles in each of the 3 axis + + + Temperature: -55 / 20 to +35 / 85 / 20to +35 10.Thermal shock Contact resistance: 70 m ohms max. + + + Time: -30 / 2 to 3 / 30 / 2 to 3 (Minutes) 10 cycles 168 hours at -10to +65 and Relative Humidity of 90% to 98% 11.Humidity Insulation resistance: 10 M ohms min. (Dry state) 7 cycles 12.Salt Spray Contact resistance: 70 m ohms max. Exposed to 5% salt water solution for 48 hours Soldering temperature: 245 13.Solderability Wet state, with solder coverage area over 95% Recommended solder immersion time: 2 to 3 seconds Materials Receptacles Part Material Finish Remarks Insulator Synthetic resin Color: Black UL94V-0 Contact area: Gold plating Contacts --------------- Copper alloy Termination area: Tin alloy plating Copper alloy Tin alloy plating Metal shield --------------- Polyamide Pick-and-place flat plate --------------- --------------- Plugs Part Material Finish Remarks Insulator UL94V-0 Synthetic resin Color: Black Contact area: Gold plating Contacts Copper alloy --------------- Termination area: Tin alloy plating Metal shield Steel Tin alloy plating --------------- Over-mold compound (Note 1) PVC Black (Note 2) --------------- Note 1: The over-mold compound is applied at the time of the termination of the plug with the cable and can not be ordered as a separate part. Note 2: The over-molding and cables can be supplied in a wide range of colors. Please contact your Hirose Electric account representative for details. 2