6ED003-F2 family 6ED003L02-F2 and 6ED003L06-F2 family 200 V and 600 V three-phase gate driver with Over Current Protection (OCP), Enable (EN) and Fault Features Product summary Infineon thin-film-SOI-technology V (6ED003L06-F2) = 620 V max. OFFSET Maximum blocking voltage +600 V V (6ED003L02-F2) = 200 V max. OFFSET Output source/sink current +0.165 A/-0.375 A I (typ.) = +0.165 A / -0.375 A O+/- Insensitivity of the bridge output to negative t / t = 530ns / 490 ns on off transient voltages up to -50 V given by SOI- t /t (typ. C =1 nF) = 60 ns / 26 ns f r L technology Separate control circuits for all six drivers Package Detection of over current and under voltage supply DSO-28 Externally programmable delay for fault clear after over current detection Shut down of all switches during error conditions Signal interlocking of every phase to prevent cross- TSSOP-28 conduction Potential applications Home appliance, refrigeration compressors, air-conditioning Fans, pumps Motor drives, general purpose inverters Power tools, light electric vehicles Product validation Qualified for industrial applications according to the relevant tests of JEDEC47/20/22. Description The devices are full bridge drivers to control power devices like MOSFET or IGBTs in 3-phase systems with a maximum blocking voltage of +600 V. Based on the used SOI-technology there is an excellent ruggedness on transient voltages. No parasitic thyristor structures are present in the device. Hence, no parasitic latch-up may occur at all temperatures and voltage conditions. The six independent drivers are controlled at the low-side using CMOS resp. LSTTL compatible signals, down to 3.3 V logic. The device includes an under-voltage detection unit with hysteresis characteristic and an over- current detection. The over-current level is adjusted by choosing the resistor value and the threshold level at pin ITRIP. Both error conditions (under-voltage and over-current) lead to a definite shut down of all six switches. An error signal is provided at the FAULT open drain output pin. The blocking time after over-current can be adjusted with an RC-network at pin RCIN. The input RCIN owns an internal current source of 2.8 A. Therefore, the resistor R is optional. The typical output current can be given with 165 mA for pull-up and 375 RCIN mA for pull down. Because of system safety reasons a 310 ns interlocking time has been realised. The function of input EN can optionally be extended with over-temperature detection, using an external NTC-resistor (see Figure 1). 6ED003-F2 family Datasheet Please read the Important Notice and Warnings at the end of this document Version 2.9 www.infineon.com/gdThreePhase 1 of 19 2019-03-21 6ED003-F2 family 200 V & 600 V three-phase driver with Over Current Protection, Enable and Fault Ordering information DC-Bus VCC VCC VB1,2,3 HIN1,2,3 HIN1,2,3 HO1,2,3 LIN1,2,3 LIN1,2,3 To Load EN EN VS1,2,3 5V FAULT FAULT LO1,2,3 R RCIN COM RCIN C RCIN ITRIP VSS R Sh VSS Figure 1 Typical application diagram Ordering information nd Table 1 Members of 6ED003-F2 family 2 generation Sales Name High side control input Typ. UVLO- Bootstra Package HIN1,2,3 and LIN1,2,3 Thresholds p diode 6ED003L06-F2 / 6ED003L02-F2 Negative logic 11.7 V / 9.8 V No DSO28 / TSSOP28 Table of contents Features ......................................................................................................................................................... 1 Product summary .......................................................................................................................................... 1 Package .......................................................................................................................................................... 1 Potential applications ................................................................................................................................... 1 Product validation ......................................................................................................................................... 1 Description ..................................................................................................................................................... 1 Ordering information ..................................................................................................................................... 2 Table of contents ........................................................................................................................................... 2 1 Block diagram ...................................................................................................................................... 3 2 Lead definitions .................................................................................................................................... 4 3 Functional description ......................................................................................................................... 5 3.1 Low Side and High Side Control Pins (Pin 2, 3, 4, 5, 6, 7) ....................................................................... 5 3.2 EN (Gate Driver Enable, Pin 10) ............................................................................................................... 5 3.3 /FAULT (Fault Feedback, Pin 8) ............................................................................................................... 6 3.4 ITRIP and RCIN (Over-Current Detection Function, Pin 9, 11) ............................................................... 6 3.5 VCC, VSS and COM (Low Side Supply, Pin 1, 12, 13) ............................................................................... 6 3.6 VB1, 2, 3 and VS1, 2, 3 (High Side Supplies, Pin 18, 20, 22, 24, 26, 28) ................................................... 6 3.7 LO1,2,3 and HO1,2,3 (Low and High Side Outputs, Pin 14, 15, 16, 19, 23, 27) ....................................... 7 4 Electrical parameters ........................................................................................................................... 8 4.1 Absolute maximum ratings ..................................................................................................................... 8 4.2 Required operation conditions ............................................................................................................... 9 6ED003-F2 family Datasheet 2 of 19 Version 2.9 www.infineon.com/gdThreePhase 2019-03-21