CY3668 WIRELESSUSB-NL DEVELOPMENT KIT
QUICK START GUIDE
2
1 2
The CY3668 DVK consists of two development boards, two Insert the CY3668 kit CD into the computers CD drive.
WUSB-NL Radio modules, one enCoRe II module, two enCoRe V
If the WirelessUSB-NL DVK installer application does not launch
modules, one MiniProg, two 12-V power adapters, one USB A/
automatically, launch it manually by clicking 'cyautorun.exe'.
Mini-B cable, one CD, and 10 jumper wires.
Click Install WirelessUSB NL DVK to install PSoC Designer,
Note: When you receive the kit, ensure that the enCoRe V modules
PSoC Programmer, and WirelessUSB-NL DVK software.
are connected on the development boards.
3 4
Key instructions for programming Bridge and Keyboard Setting up the Keyboard
Do not attach the WUSB-NL module to development boards. Program the other development board with the keyboard
firmware located at <Install_Directory>\Cypress\ CY3668
Do not attach any power source (AC-DC adapter or USB
DVK\1.0\ Firmware\ Keyboard\ NL_Keyboard_enCoReV\
cable) to development boards.
NL_Keyboard_enCoReV\NL_Keyboard_enCoReV.hex. Use
Setting up the Bridge
the same procedure as for the Bridge.
Program one of the development boards with the Bridge firm-
Attach the following wires from P7 to P10: P0_3 to S1, P0_4 to
ware that is located at <Install_Directory>\
S2, P0_5 to S3, P0_6 to S5, P0_0 to LED1, P0_1 to LED2, and
Cypress\CY3668 DVK\1.0\Firmware\Bridge\
P0_2 to LED3.
NL_Bridge_enCoReV\NL_Bridge_enCoReV\
Plug in the WUSB-NL module on the development board.
NL_Bridge_enCoReV.hex. See the user guide for the program-
ming procedure.
Power the keyboard using the 12-V power adapter.
Note: The default install directory isC:\Program File or
Establish Wireless Link and Data TransferC:\Program Files (x86
Press and release S1 on the Bridge to change to Bind mode.
Attach the following wires from P7 to P10: P0_3 to S1, P0_0
LED1 on the Bridge blinks to denote Bind mode. Press and
to LED1, and P0_1 to LED2.
release S5 on the Keyboard to change to Bind mode; wait for 2
seconds. On successful binding, LED1 on the Bridge switches off
Plug in the WUSB-NL module on the development board
and the wireless link is now ready for data transfer
Connect the Bridge to the computer using the USB cable
On the Keyboard, press and release S1 for Num Lock, S2 for
If the LCD panel text is not visible, increase the LCD contrast by rotat-
Caps Lock, and S3 for Scroll Lock. The actions corresponding to
ing the knob located below the LCD panel in clockwise direction.
the pressed key are executed on the computer.CY3668 WIRELESSUSB-NL DEVELOPMENT KIT
QUICK START GUIDE
CY3668 Development Board Details
Voltage
LCD
Regulator
12VDCSupply
PowerSelection
Jumper
LCDContrast
Potentiometer
BreadboardArea
WirelessUSBNL
RadioInterface
Switches
MiniBUSB
Connector
LEDs
OCDConnector Output
VoltageLevel
Potentiometer
Logic
AnalyzerHeader
SwitchtoselectenCoRe
IIorenCoReVfor
Programming
enCoReII/enCoReV Reset
ISSP
I2C
ModuleInterface Switch
Header
Header
enCoRe II Module* WirelessUSB-NL Radio Module enCoRe V Module
* Refer to the user guide for details on example projects using the enCoRe II module.
For the latest information about this kit, visit