EVALM1183MTOBO1 Infineon

AN2017-13 EVAL-M1-183M User Manual EVAL-M1-183M User Manual iMOTION Modular Application Design Kit About this document Scope and purpose This application note provides an overview of the evaluation board EVAL-M1-183M including its main features, key data, pin assignments, mechanical dimensions and its application. EVAL-M1-183M is an evaluation-board as part of the iMOTION Modular Application Design Kit (MADK). This board features and demonstrates Infineons advanced Motion Control Engine (MCE) for permanent magnet motors drive over the full speed range. The evaluation board EVAL-M1-183M was developed to support customers during their first steps designing applications with running any permanent magnet motor via sensorless sinusoidal control. Intended audience This application note is intended for all technical specialists working for motor control with the EVAL-M1-183M board under laboratory conditions. Table of Contents About this document ....................................................................................................................... 1 Table of Contents ........................................................................................................................... 1 1 Safety precautions ......................................................................................................... 2 2 Introduction .................................................................................................................. 3 3 Main features ................................................................................................................ 4 3.1 Key data ................................................................................................................................................... 5 3.2 IRMCF183 installer ................................................................................................................................... 7 4 Pin assignments ............................................................................................................ 8 5 Getting Started with EVAL-M1-183M ............................................................................... 10 5.1 Setting up the system............................................................................................................................ 10 5.2 iMOTION development tools and software ....................................................................................... 12 5.2.1 MCEProgrammer setup overview .................................................................................................... 12 5.2.2 MCEWizard setup overview .............................................................................................................. 14 5.2.3 MCEDesigner setup overview .......................................................................................................... 16 6 Schematics and Layout .................................................................................................. 17 6.1 IRMCF183M Schematic Overview .......................................................................................................... 17 6.2 Current feedback ................................................................................................................................... 18 6.3 AD port Input ......................................................................................................................................... 19 6.4 PCB Layout ............................................................................................................................................ 20 7 Bill of Materials of EVAL-M1-183M ................................................................................... 23 8 Reference .................................................................................................................... 25 Revision History ............................................................................................................................ 26 User Manual Please read the Important Notice and Warnings at the end of this document <Revision 1.2> www.infineon.com <2018-06-27> EVAL-M1-183M User Manual iMOTION Modular Application Design Kit Safety precautions 1 Safety precautions In addition to the precautions listed throughout this manual, please read and understand the following statements regarding hazards associated with development systems. Table 1 Precautions Attention: The ground potential of the EVAL-M1-183M system is biased to a negative DC bus voltage potential. When measuring voltage waveform by oscilloscope, the scopes ground needs to be isolated. Failure to do so may result in equipment damage or personal injury or death. Attention: Only personnel familiar with the drive and associated machinery should plan or implement the installation, start-up and subsequent maintenance of the system. Failure to comply may result in personal injury and/or equipment damage. Attention: The surfaces of the drive may become hot, which may cause injury. Attention: EVAL-M1-183M system contains parts and assemblies sensitive to Electrostatic Discharge (ESD). Electrostatic control precautions are required when installing, testing, servicing or repairing this assembly. Component damage may result if ESD control procedures are not followed. If you are not familiar with electrostatic control procedures, refer to applicable ESD protection handbooks and guidelines. Attention: A control board, incorrectly applied or installed, can result in component damage or reduction in product lifetime. Wiring or application errors such as under sizing the motor, supplying an incorrect or inadequate DC supply or excessive ambient temperatures may result in system malfunction. Attention: Remove or connect this control board from or to the power drive. Wait three minutes after removing power from the power drive to discharge the bus capacitors. Do not attempt to service the drive until the bus capacitors have discharged to zero. Failure to do so may result in personal injury or death. Attention: EVAL-M1-183M system is shipped with packing materials that need to be removed prior to installation. Failure to remove all packing materials which are unnecessary for system installation may result in overheating or abnormal operating condition. User Manual 2 <Revision 1.2> <2018-06-27>