EVALM3CM615PNTOBO1 Infineon

AN2017-15 EVAL-M3-CM615PN User Manual EVAL-M3-CM615PN User Manual iMOTION Modular Application Design Kit About this document Scope and purpose This user manual provides an overview of the evaluation board Eval-M3-CM615PN including its main features, key data, pin assignments and mechanical dimensions. Eval-M3-CM615PN is an evaluation board as part of the iMOTION Modular Application Design Kit. This power board includes a PFC integrated 3-phase CIPOS Mini Intelligent Power Module (IPM) for motor drive application. In combination with the control board equipped with the M3 30pin interface connector such as EVAL-M3-102T, it features and demonstrates Infineons CIPOS Mini IPM technology and Advanced Motion Control Engine (MCE 2.0) technology for permanent magnet motors drive over the full speed range. The inverter section has 600V of voltage and 15A of current rating, and the PFC section has 650V of voltage and 30A of current rating. It is optimized to major home appliances like air conditioners and low power motor dirve application with high frequency switching operation of power factor correction. This evaluation board Eval-M3-CM615PN was developed to support customers during their first steps designing applications with CIPOS Mini PFC integrated IPM IFCM15P60GD and running any permanent magnet motor via sensorless sinusoidal control. Intended audience This user manual is intended for all technical specialists who know motor control and high power electronics converter and this board is intended to be used under laboratory conditions. Table of contents About this document ....................................................................................................................... 1 Table of contents ............................................................................................................................ 1 1 Safety precautions ................................................................................................................. 3 2 Introduction .......................................................................................................................... 4 3 EVAL-M3-CM615PN main features ............................................................................................ 6 3.1 EVAL-M3- CM615PN board specifications ............................................................................................... 7 3.2 Pin assignment ........................................................................................................................................ 9 4 Getting Started with EVAL-M3-CM615PN .................................................................................. 11 4.1 Setting up the system............................................................................................................................ 11 4.2 iMOTION development tools and software ....................................................................................... 13 4.2.1 MCEWizard setup overview .............................................................................................................. 13 4.2.2 MCEDesigner setup overview .......................................................................................................... 15 5 Hardware description of EVAL-M3-CM615PN ............................................................................ 17 5.1 Boost PFC section using CIPOS mini IPM ........................................................................................... 17 5.1.1 AC Voltage sensing and MCEWizard configuration ......................................................................... 17 5.1.2 Hardware Modification for AC Voltage sensing to work with IRMCF188 ........................................ 19 5.1.3 PFC External Current feedback configuration and calculation ...................................................... 19 5.1.4 PFC Overcurrent protection circuit and PFC Gatekill configuration .............................................. 20 User Manual Please read the Important Notice and Warnings at the end of this document Revision 1.4 www.infineon.com page 1 of 41 2019-10-11 EVAL-M3-CM615PN User Manual iMOTION Modular Application Design Kit Table of contents 5.2 Inverter section using CIPOS mini IPM ............................................................................................... 21 5.2.1 DC bus sensing and MCEWizard configuration ............................................................................... 22 5.2.2 Motor External Current feedback configuration and calculation .................................................. 23 5.2.3 Inverter Overcurrent protection and Motor Gatekill configuration ............................................... 25 5.3 Thermistor/NTC Characteristics and protection calculation .............................................................. 26 5.3.1 CIPOS Internal NTC Thermistor Characteristics ........................................................................ 26 5.3.2 Overtemperature Hardware Protection Circuit .............................................................................. 27 5.3.3 NTC shutdown value calculation and configuration ...................................................................... 27 5.4 Auxiliary power supply .......................................................................................................................... 28 5.5 Schematics for EVAL-M3- CM615PN ...................................................................................................... 28 5.6 PCB Layout for EVAL-M3- CM615PN ...................................................................................................... 32 6 Bill of material ...................................................................................................................... 36 7 Reference ............................................................................................................................. 39 Revision history............................................................................................................................. 40 User Manual 2 of 41 Revision 1.4 2019-10-11