IR21084STRPBF Infineon

Data Sheet No. PD60161-R ( ) & (PbF) IR2108(4) S Features HALF-BRIDGE DRIVER Floating channel designed for bootstrap operation Fully operational to +600V Packages Tolerant to negative transient voltage dV/dt immune 14-Lead SOIC 8-Lead SOIC Gate drive supply range from 10 to 20V IR2108S IR21084S Undervoltage lockout for both channels 3.3V, 5V and 15V input logic compatible 14-Lead PDIP Cross-conduction prevention logic IR21084 Matched propagation delay for both channels High side output in phase with HIN input 8-Lead PDIP Low side output out of phase with LIN input IR2108 Logic and power ground +/- 5V offset. Internal 540ns dead-time, and 2106/2301//2108//2109/2302/2304 Feature Comparison programmable up to 5us with one external R resistor (IR21084) DT Cross- Input conduction Lower di/dt gate driver for better Part Dead-Time Ground Pins logic prevention noise immunity logic Available in Lead-Free 2106/2301 COM HIN/LIN no none 21064 VSS/COM 2108 Internal 540ns COM Description HIN/LIN yes 21084 Programmable 0.54~5 s VSS/COM The IR2108(4)(S) are high voltage, high speed 2109/2302 Internal 540ns COM IN/SD yes power MOSFET and IGBT drivers with depen- 21094 Programmable 0.54~5 s VSS/COM dent high and low side referenced output 2304 HIN/LIN yes Internal 100ns COM channels. Proprietary HVIC and latch immune CMOS technologies enable ruggedized monolithic construction. The logic input is compatible with standard CMOS or LSTTL output, down to 3.3V logic. The output drivers feature a high pulse current buffer stage designed for minimum driver cross-conduction. The floating channel can be used to drive an N-channel power MOSFET or IGBT in the high side configuration which operates up to 600 volts. Typical Connection up to 600V V CC V V CC B HIN HIN HO TO LIN LIN V S LOAD COM LO up to 600V IR21084 HO IR2108 V V V CC CC B HIN V HIN S TO LOAD LIN LIN DT (Refer to Lead Assignments for correct pin V V COM SS configuration). This/These diagram(s) show SS R DT LO electrical connections only. Please refer to our Application Notes and DesignTips for proper circuit board layout. www.irf.com 1( ) & (PbF) IR2108(4) S Absolute Maximum Ratings Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage param- eters are absolute voltages referenced to COM. The thermal resistance and power dissipation ratings are measured under board mounted and still air conditions. Symbol Definition Min. Max. Units V High side floating absolute voltage -0.3 625 B V High side floating supply offset voltage V - 25 V + 0.3 S B B V High side floating output voltage V - 0.3 V + 0.3 HO S B V Low side and logic fixed supply voltage -0.3 25 CC V V Low side output voltage -0.3 V + 0.3 LO CC DT Programmable dead-time pin voltage (IR21084 only) V - 0.3 V + 0.3 SS CC V Logic input voltage (HIN & LIN)V - 0.3 V + 0.3 IN SS CC V Logic ground (IR21084 only) V - 25 V + 0.3 SS CC CC dV /dt Allowable offset supply voltage transient 50 V/ns S P Package power dissipation T +25 C (8 lead PDIP) 1.0 D A (8 lead SOIC) 0.625 (14 lead PDIP) 1.6 W (14 lead SOIC) 1.0 Rth Thermal resistance, junction to ambient (8 lead PDIP) 125 JA (8 lead SOIC) 200 (14 lead PDIP) 75 C/W (14 lead SOIC) 120 T Junction temperature 150 J T Storage temperature -50 150 C S T Lead temperature (soldering, 10 seconds) 300 L Recommended Operating Conditions The Input/Output logic timing diagram is shown in figure 1. For proper operation the device should be used within the recommended conditions. The V and V offset rating are tested with all supplies biased at 15V differential. S SS Symbol Definition Min. Max. Units VB High side floating supply absolute voltage V + 10 V + 20 S S V High side floating supply offset voltage Note 1 600 S V High side floating output voltage V V HO S B V Low side and logic fixed supply voltage 10 20 CC V Low side output voltage 0 V V LO CC V Logic input voltage IR2108 COM V IN CC IR21084 V V SS CC DT Programmable dead-time pin voltage (IR21084 only) V V SS CC V Logic ground (IR21084 only) -5 5 SS C T Ambient temperature -40 125 A Note 1: Logic operational for V of -5 to +600V. Logic state held for V of -5V to -V . (Please refer to the Design Tip S S BS DT97-3 for more details). 2 www.irf.com