Data Sheet No. PD60107 revY IR2133/IR2135(J&S) & (PbF) IR2233/IR2235(J&S) & (PbF) 3-PHASE BRIDGE DRIVER Features Product Summary Floating channel designed for bootstrap operation Fully operational to +600V or+1200V V 600V or 1200V max. OFFSET Tolerant to negative transient voltage dV/dt immune I +/- 200 mA / 420 mA O Gate drive supply range from 10V/12V to 20V DC and up to 25V for transient V 10 - 20V or 12 - 20V OUT Undervoltage lockout for all channels Over-current shut down turns off all six drivers t (typ.) 750/700 ns on/off Independent 3 half-bridge drivers Deadtime (typ.) 250 ns Matched propagation delay for all channels 2.5V logic compatible Outputs out of phase with inputs Packages All parts are also available LEAD-FREE Description The IR2133IR2135/IR2233IR2355 (J&S) are high voltage, high speed power MOSFET and IGBT driver with three independent high side and low side referenced output channels for 3-phase applications. Propri- 28-Lead SOIC etary HVIC technology enables ruggedized monolithic construction. 28-Lead PDIP Logic inputs are compatible with CMOS or LSTTL outputs, down to 2.5V logic. An independent operational amplifier provides an analog 44-Lead PLCC w/o 12 leads feedback of bridge current via an external current sense resistor. A current trip function which terminates all six outputs can also be de- rived from this resistor. A shutdown function is available to terminate all six outputs. An open drain FAULT signal is provided to indicate that an over-current or undervoltage shutdown has occurred. Fault conditions are cleared with the FLT-CLR lead. The output drivers feature a high pulse current buffer stage designed for minimum driver cross-conduction. Propagation delays are matched to simplify use in high frequency applications. The floating channels can be used to drive N-channel power MOSFETs or IGBTs in the high side configuration which operates up to 600 volts or 1200 volts. Typical Connection up to 600V or 1200V (Refer to Lead Assignments for correct pin configuration). This/These diagram(s) show electrical connections only. Please refer to our Application Notes and DesignTips for proper circuit board layout. www.irf.com 1/ ) & (PbF) IR2133/IR2135/IR2233 IR2235(J&S Absolute Maximum Ratings Absolute Maximum Ratings indicate sustained limits beyond which damage to the device may occur. All volt- age parameters are absolute voltages referenced to COM. The Thermal Resistance and Power Dissipation ratings are measured under board mounted and still air conditions. Symbol Definition Min. Max. Units V High side floating supply voltage (IR2133/IR2135) -0.3 625 B1,2,3 (IR2233/IR2235) -0.3 1225 V High side floating supply offset voltage V - 25 V + 0.3 S1,2,3 B1,2,3 B1,2,3 V High side floating output voltage V - 0.3 V + 0.3 HO1,2,3 S1,2,3 B1,2,3 V Fixed supply voltage -0.3 25 CC V Logic ground V - 25 V + 0.3 SS CC CC V V Low side output voltage -0.3 V + 0.3 LO1,2,3 CC VIN Logic input voltage (HIN, LIN, ITRIP, SD & FLT-CLR) VSS - 0.3 (VSS + 15) or (V + 0.3) CC whichever is lower V Op amp input voltage (CA+ & CA-) V - 0.3 V + 0.3 IN,AMP SS CC V Op amp output voltage (CAO) V - 0.3 V + 0.3 OUT,AMP SS CC output voltage V FAULT V - 0.3 V + 0.3 FLT SS CC V/ns dVS/dt Allowable offset supply voltage transient 50 P Package power dissipation T 25C (28 Lead PDIP) 1.5 D A W (28 Lead SOIC) 1.6 (44 lead PLCC) 2.0 Rth Thermal resistance, junction to ambient (28 Lead PDIP) 83 JA C/W (28 Lead SOIC) 78 (44 lead PLCC) 63 T Junction temperature 125 J C TS Storage temperature -55 150 T Lead temperature (soldering, 10 seconds 300 L Recommended Operating Conditions The input/output logic timing diagram is shown in figure 1. For proper operation the device should be used within the recommended conditions. All voltage parameters are absolute voltages referenced to COM. The V offset rating is S tested with all supplies biased at 15V differential. Symbol Parameter Definition Min. Max. Units V High side floating supply voltage V + 10/12 V + 20 B1,2,3 S1,2,3 S1,2,3 High side floating supply offset voltage (IR2133/IR2135) Note 1 600 VS1,2,3 (IR2233/IR2235) Note 1 1200 VHO1,2,3 High side floating output voltage VS1,2,3 VB1,2,3 V Fixed supply voltage 10 or 12 20 CC V Low side driver return -5 5 SS V VLO1,2,3 Low side output voltage 0 VCC V Logic input voltage (HIN, LIN, ITRIP, SD & FLT-CLR) V V + 5 IN SS SS V Op amp input voltage (CA+ & CA-) V V + 5 IN,AMP SS SS V Op amp output voltage (CAO) V V + 5 OUT,AMP SS SS output voltage V FAULT V V FLT SS CC Note 1: Logic operational for V of COM - 4V to COM + 600V/1200V. Logic state held for V of COM -4V to COM -V . (Please refer to the Design Tip S S BS DT97-3 for more details). Note 2: All input pins, op amp input and output pins are internally clamped with a 5.2V zener diode. 2 www.irf.com