MB95630H Series New 8FX 8-bit Microcontrollers The MB95630H Series is a series of general-purpose, single-chip microcontrollers. In addition to a compact instruction set, the microcontrollers of this series contain a variety of peripheral functions. Capable of clock asynchronous serial data transfer and clock Features synchronous serial data transfer 2 F MC-8FX CPU core External interrupt 10 channels Instruction set optimized for controllers Interrupt by edge detection (rising edge, falling edge, and Multiplication and division instructions both edges can be selected) 16-bit arithmetic operations Can be used to wake up the device from different low power consumption (standby) modes Bit test branch instructions Bit manipulation instructions, etc. 8/10-bit A/D converter 8 channels 8-bit or 10-bit resolution can be selected. Clock Low power consumption (standby) modes Selectable main clock source Main oscillation clock (up to 16.25 MHz, maximum ma- There are four standby modes as follows: chine clock frequency: 8.125 MHz) Stop mode External clock (up to 32.5 MHz, maximum machine clock Sleep mode frequency: 16.25 MHz) Watch mode Main CR clock (4 MHz 2%) Time-base timer mode Main CR PLL clock In standby mode, two further options can be selected: normal - The main CR PLL clock frequency becomes 8 MHz standby mode and deep standby mode. 2% when the PLL multiplication rate is 2. I/O port - The main CR PLL clock frequency becomes 10 MHz MB95F632H/F633H/F634H/F636H (number of I/O ports: 28) 2% when the PLL multiplication rate is 2.5. - The main CR PLL clock frequency becomes 12 MHz General-purpose I/O ports (CMOS I/O): 25 2% when the PLL multiplication rate is 3. General-purpose I/O ports (N-ch open drain): 3 - The main CR PLL clock frequency becomes 16 MHz MB95F632K/F633K/F634K/F636K (number of I/O ports: 29) 2% when the PLL multiplication rate is 4. General-purpose I/O ports (CMOS I/O): 25 Selectable subclock source General-purpose I/O ports (N-ch open drain): 4 Suboscillation clock (32.768 kHz) On-chip debug External clock (32.768 kHz) 1-wire serial control Sub-CR clock (Typ: 100 kHz, Min: 50 kHz, Max: 150 kHz) Serial writing supported (asynchronous mode) Timer Hardware/software watchdog timer 8/16-bit composite timer 2 channels Built-in hardware watchdog timer 8/16-bit PPG 3 channels Built-in software watchdog timer 16-bit PPG timer 1 channel (can work independently or together with the multi-pulse generator) Power-on reset 16-bit reload timer 1 channel (can work independently or A power-on reset is generated when the power is switched together with the multi-pulse generator) on. Time-base timer 1 channel Low-voltage detection reset circuit (only available on Watch prescaler 1 channel MB95F632K/F633K/F634K/F636K) UART/SIO 1 channel Built-in low-voltage detection function (The combination of Full duplex double buffer detection voltage and release voltage can be selected from four options.) Capable of clock asynchronous (UART) serial data transfer and clock synchronous (SIO) serial data transfer Comparator 2 I C bus interface 1 channel Clock supervisor counter Built-in wake-up function Built-in clock supervisor counter Multi-pulse generator (MPG) (for DC motor control) 1 channel Dual operation Flash memory 16-bit reload timer 1 channel The program/erase operation and the read operation can be 16-bit PPG timer 1 channel executed in different banks (upper bank/lower bank) simul- Waveform sequencer (including a 16-bit timer equipped with taneously. a buffer and a compare clear function) Flash memory security function LIN-UART Protects the content of the Flash memory. Full duplex double buffer Cypress Semiconductor Corporation 198 Champion Court San Jose, CA 95134-1709 408-943-2600 Document Number: 002-04627 Rev. *A Revised March 29, 2016 MB95630H Series 15. I/O Ports..................................................................... 30 Contents 15.1 Port 0................................................................. 31 Features............................................................................. 1 15.2 Port 1................................................................. 39 15.3 Port 6................................................................. 46 1. Product Line-up ............................................................ 3 15.4 Port F................................................................. 51 2. Packages And Corresponding Products.................... 5 15.5 Port G................................................................ 53 3. Differences Among Products And Notes On 16. Interrupt Source Table ............................................. 56 Product Selection ............................................................. 5 17. Pin States In Each Mode.......................................... 57 4. Pin Assignment ............................................................ 6 18. Electrical Characteristics......................................... 61 5. Pin Functions................................................................ 8 18.1 Absolute Maximum Ratings............................... 61 6. I/O Circuit Type ........................................................... 12 18.2 Recommended Operating Conditions ............... 63 7. Handling Precautions................................................. 14 18.3 DC Characteristics ............................................ 64 7.1 Precautions for Product Design........................... 14 18.4 AC Characteristics............................................. 67 7.2 Precautions for Package Mounting ..................... 15 18.5 A/D Converter................................................... 85 7.3 Precautions for Use Environment........................ 17 18.6 Flash Memory Program/Erase Characteristics.. 89 8. Notes On Device Handling......................................... 17 19. Sample Characteristics............................................ 90 9. Pin Connection ........................................................... 18 20. Mask Options............................................................ 97 10. Block Diagram .......................................................... 19 21. Ordering Information................................................ 97 11. CPU Core................................................................... 20 22. Package Dimension.................................................. 98 12. Memory Space .......................................................... 21 23. Major Changes In This Edition.............................. 101 Document History Page............................................... 101 13. Areas For Specific Applications ............................. 23 Sales, Solutions, and Legal Information .................... 102 14. I/O Map....................................................................... 24 Document Number: 002-04627 Rev. *A Page 2 of 102