TLE9251VLEXUMA1 Infineon

TLE9251V High Speed CAN Transceiver 1 Overview Features Fully compliant to ISO 11898-2 (2016) and SAE J2284-4/-5 PG-TSON-8 Reference device and part of Interoperability Test Specification for CAN Transceiver Guaranteed loop delay symmetry for CAN FD data frames up to 5 MBit/s Very low electromagnetic emission (EME) allows the use without additional common mode choke V input for voltage adaption to the C interface (3.3V & 5V) IO Bus Wake-up Pattern (WUP) function with optimized filter time (0.5s - 1.8s) for worldwide OEM usage PG-DSO-8 Stand-by mode with minimized quiescent current Transmitter supply V can be turned off in Stand-by Mode for additional CC quiescent current savings Wake-up indication on the RxD output Wide common mode range for electromagnetic immunity (EMI) Excellent ESD robustness +/-8kV (HBM) and +/-11kV (IEC 61000-4-2) Extended supply range on the V and V supply CC IO CAN short circuit proof to ground, battery, V and V CC IO TxD time-out function Very low CAN bus leakage current in power-down state Overtemperature protection Protected against automotive transients according ISO 7637 and SAE J2962-2 standards Green Product (RoHS compliant) Small, leadless TSON8 package designed for automated optical inspection (AOI) Potential applications Gateway Modules Body Control Modules (BCM) Engine Control Unit (ECUs) Datasheet 1 Rev. 1.11 www.infineon.com/automotive-transceiver 2019-09-19High Speed CAN Transceiver TLE9251V Overview Product validation Qualified for automotive applications. Product validation according to AEC-Q100. Description Type Package Marking TLE9251VLE PG-TSON-8 9251V TLE9251VSJ PG-DSO-8 9251V The TLE9251V is the latest Infineon high-speed CAN transceiver generation, used inside HS CAN networks for automotive and also for industrial applications. It is designed to fulfill the requirements of ISO 11898-2 (2016) physical layer specification and respectively also the SAE standards J1939 and J2284. The TLE9251V is available in a PG-DSO-8 package and in a small, leadless PG-TSON-8 package. Both packages are RoHS compliant and halogen free. The PG-TSON-8 package supports the solder joint requirements for automated optical inspection (AOI). As an interface between the physical bus layer and the HS CAN protocol controller, the TLE9251V protects the microcontroller against interferences generated inside the network. A very high ESD robustness and the perfect RF immunity allows the use in automotive applications without adding additional protection devices, like suppressor diodes for example. While the transceiver TLE9251V is not supplied the bus is switched off and illustrates an ideal passive behavior with the lowest possible load to all other subscribers of the HS CAN network. Based on the high symmetry of the CANH and CANL output signals, the TLE9251V provides a very low level of electromagnetic emission (EME) within a wide frequency range. The TLE9251V fulfills even stringent EMC test limits without additional external circuit, like a common mode choke for example. The perfect transmitter symmetry combined with the optimized delay symmetry of the receiver enables the TLE9251V to support CAN FD data frames. Depending on the size of the network and the along coming parasitic effects the device supports bit rates up to 5 MBit/s. Dedicated low-power modes, like Stand-by mode provide very low quiescent currents while the device is powered up. In Stand-by mode the typical quiescent current on V is below 10 A while the device can still be IO woken up by a bus signal on the HS CAN bus. Fail-safe features like overtemperature protection, output current limitation or the TxD time-out feature protect the TLE9251V and the external circuitry from irreparable damage. Datasheet 2 Rev. 1.11 2019-09-19