CPC1708J IXYS

CPC1708J 60V, 11.85A Single-Pole Normally Open DC-Only Power Relay INTEGRATED CIRCUITS DIVISION Characteristics Description IXYS Integrated Circuits brings OptoMOS Parameter Rating Units technology, reliability and compact size to a new family V Blocking Voltage 60 P of High Power Solid State Relays. As part of this new family, the CPC1708J single-pole normally open Load Current, T =25C: A (1-Form-A) DC Solid State Relay employs optically With 5C/W Heat Sink 11.85 coupled MOSFET technology to provide 2500V of A rms DC No Heat Sink 4 input to output isolation. On-Resistance (max) 0.08 The relay output is constructed with efficient MOSFET Thermal Impedance, switches that use IXYS Integrated Circuits patented Junction-to-Case, JC 0.35 C/W OptoMOS architecture. The input, a highly efficient infrared LED, controls the optically coupled output. Features Low on-resistance and high load current handling 11.85A Load Current with 5C/W Heat Sink capability make this relay suitable for a variety of high DC Low 0.08 On-Resistance performance DC switching applications. 60V Blocking Voltage P 2500V Input/Output Isolation The unique i4-PAC package pioneered by IXYS rms Low Thermal Impedance: = 0.35 C/W enables solid state relays to achieve the highest load JC Isolated, Low Thermal Impedance Ceramic Pad for current and power ratings. This package features an Heat Sink Applications IXYS-unique process where the silicon chips are soft Low Drive Power Requirements soldered onto the Direct Copper Bond (DCB) No EMI/RFI Generation substrate instead of the usual copper leadframe. The Flammability Rating UL 94 V-0 DCB ceramic, the same substrate used in high power modules, not only provides 2500V isolation but also rms Applications very low junction-to-case thermal impedance Industrial Controls / Motor Control (0.35C/W). Robotics Medical EquipmentPatient/Equipment Isolation Instrumentation Multiplexers Ordering Information Data Acquisition Electronic Switching Part Descript io n I/O Subsystems CPC1708J i4-PAC Package (25 per tube) Meters (Watt-Hour, Water, Gas) Transportation Equipment Switching Characteristics Approvals UL 508 Certified Component: File E69938 Form-A Pin Configuration I F 12 3 4 90% 10% +- - + I LOAD t t on off DS-CPC1708J - R10 www.ixysic.com 1CPC1708J INTEGRATED CIRCUITS DIVISION 1 Specifications 1.1 Absolute Maximum Ratings 25C Absolute maximum ratings are stress ratings. Stresses in Parameter Symbol Rating Unit excess of these ratings can cause permanent damage to V V Blocking Voltage 60 L P the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this V Reverse Input Voltage 5V R data sheet is not implied. Input Control Current, 50 mA I Continuous F Typical values are characteristic of the device at +25C, Peak (10ms) 1 A and are the result of engineering evaluations. They are P 150 mW provided for information purposes only, and are not part of Input Power Dissipation IN the manufacturing testing requirements. Isolation Voltage (Input to Output) V 2500 V ISO rms T Operating Temperature, Ambient -40 to +85 C A Storage Temperature - -40 to +125 C 1.2 Electrical Characteristics 25C Parameter Conditions Symbol Minimum Typical Maximum Units Output Characteristics I =1A V Blocking Voltage L 60 - - V DRM 1 Load Current Peak t10ms A 30 P Continuous No Heat Sink I 4 L -- Continuous T =25C A C 24 DC T =99C Continuous I C L(99) 5.35 2 I =10mA, I =1A R On-Resistance F L - 0.05 0.08 ON Off-State Leakage Current V =60V I L P -- 1 A LEAK Switching Speeds Turn-On t on -5 20 I =20mA, V =10V F L ms Turn-Off t -0.13 5 off =0mA, V =25V, f=1MHz Output Capacitance I C F L - 1250 - pF out Input Characteristics 3 I =1A I Input Control Current to Activate L F -- 10 mA Input Control Current to Deactivate - I 0.6 - - mA F I =10mA Input Voltage Drop V F 0.9 1.42 1.56 V F V =5V Reverse Input Current I R R -- 10 A Input/Output Characteristics V =0V, f=1MHz Capacitance, Input-to-Output C IO -1- pF IO 1 Higher load currents possible with proper heat sinking. 2 Measurement taken within 1 second of on-time. 3 For applications requiring high temperature operation (> 60C) a minimum LED drive current of 20mA is recommended. R10 www.ixysic.com 2