CPC1965G IXYS

CPC1965G AC Solid State Relay INTEGRATED CIRCUITS DIVISION Description Parameter Rating Units The CPC1965G is an AC Solid State Switch using AC Operating Voltage 260 V rms patented waveguide coupling with dual power SCR Load Current 1 A rms outputs to produce an alternative to optocoupler and On State Voltage Drop 1.6 V (at I = 1A ) rms L rms Triac circuits. The switches are robust enough to provide a blocking voltage of up to 600V . In addition, P tightly controlled zero-cross circuitry ensures switching Features of AC loads without the generation of transients. Load Current up to 1A rms The input and output circuits are optically coupled 600V Blocking Voltage P to provide 3750V of isolation and noise immunity rms 5mA Sensitivity between control and load circuits. As a result, the Zero-Crossing Detection CPC1965G is well suited for industrial environments DC Control, AC Output where electromagnetic interference could disrupt the Optically Isolated operation of electromechanical relays. TTL and CMOS Compatible Low EMI and RFI Generation High Noise Immunity Approvals Machine Insertable, Wave Solderable UL Recognized Component: File E69938 Flammability Classification Rating of V-0 CSA Certified Component: File 043639 Applications Ordering Information Programmable Control Process Control Part Description Power Control Panels CPC1965G 4-Pin (16-Pin Body) DIP (25/Tube) Remote Switching Gas Pump Electronics Contactors Large Relays Pin Configuration Solenoids Motors 1 16 + LED Heaters LED ZC 10 AC Load 8 AC Load DS-CPC1965G-R07 1 www.ixysic.comCPC1965G INTEGRATED CIRCUITS DIVISION Absolute Maximum Ratings 25C Absolute Maximum Ratings are stress ratings. Stresses in Parameter Ratings Units excess of these ratings can cause permanent damage to Blocking Voltage 600 V P the device. Functional operation of the device at conditions Reverse Input Voltage 5 V beyond those indicated in the operational sections of this Input Control Current 100 mA data sheet is not implied. Peak (10ms) 1A 1 Input Power Dissipation 150 mW 2 PD , Total Package Dissipation 1600 mW Isolation Voltage, Input to Output 3750 V rms Operational Temperature -40 to +85 C Storage Temperature -40 to +125 C 1 Derate linearly 1.33 mW / C 2 Derate linearly 16.6 mW / C Electrical Characteristics 25C Parameters Conditions Symbol Min Typ Max Units Output Characteristics Operating Voltage Range V - 20 - 260 V L rms Load Current, Continuous V =120-260V I 0.005 - 1.0 A L rms L rms Non-Repetitive Single Cycle Surge Current - I - - 10 A TSM Off State Leakage Current V =600V I -- 1 mA L P LEAK On-State Voltage Drop I =1A - - 1.6 V L rms rms 3 Critical Rate of Rise - dV/dt 1000 - - V/s Switching Speeds Turn-on t - - 0.5 on I =5 mA cycles F Turn-off t - - 0.5 off 1 Zero-Cross Turn-On Voltage 1st half-cycle - - 2 10 V Subsequent half-cycle - - 1 - V Operating Frequency - - 20 - 400 Hz 2 Load Power Factor for Guaranteed Turn-On - PF 0.25 - - - Input Characteristics 4 Input Control Current to Activate -I - 0.8 5 mA F Input Voltage Drop I =5mA V 0.9 1.2 1.4 V F F Input Drop-out Voltage - - 0.8 - - V Reverse Input Current V =5V I - - 10 A R R Common Characteristics Input to Output Capacitance - C -3 - pF I/O 1 Zero Cross 1st half-cycle <100Hz 2 Snubber circuits may be required at low power factors. 3 Tested in accordance with EIA/NARM standard RS-443. 4 For high noise environments, use I =10mA. F R07 2 www.ixysic.com