CPC1968J 500V Single-Pole, Normally Open Power Relay INTEGRATED CIRCUITS DIVISION Characteristics Description The CPC1968J single-pole normally open (1-Form-A) Parameter Rating Units Solid State Power Relay is rated for up to 5A V Blocking Voltage 500 P continuous load current with a 5C/W heat sink. Load Current, T =25C: A Optically coupled MOSFET technology enables the With 5C/W Heat Sink 5 CPC1968J to provide 2500V of input to output A / A rms rms DC No Heat Sink 2 isolation. The output, constructed with efficient On-Resistance 0.35 MOSFET switches and photovoltaic die, uses IXYS Integrated Circuits patented OptoMOS architecture Thermal Impedance, Junction-to-Case, while the input, a highly efficient infrared LED, JC 0.3 C/W provides the optically coupled control. The combination of low on-resistance and high load Features current handling capability makes this relay suitable 5A Load Current with 5C/W Heat Sink for a variety of high performance switching Low 0.35 On-Resistance applications. 500V Blocking Voltage P 2500V Input/Output Isolation The unique ISOPLUS-264 package pioneered by rms IXYS enables Solid State Relays to achieve the Low Thermal Impedance: = 0.3 C/W JC highest load current and power ratings. This package Isolated, Low Thermal Impedance Ceramic Pad for features a unique IXYS process in which the silicon Heat Sink Applications chips are soft soldered onto the Direct Copper Bond Low Drive Power Requirements (DCB) substrate instead of the traditional copper No EMI/RFI Generation leadframe. The DCB ceramic, the same substrate Flammability Rating UL 94 V-0 used in high power modules, not only provides Applications 2500V isolation, but also very low junction-to-case rms thermal impedance (0.3 C/W). Industrial Controls / Motor Control Robotics Medical EquipmentPatient/Equipment Isolation Ordering Information Instrumentation Multiplexers Part Descript io n Data Acquisition CPC1968J ISOPLUS-264 Package (25 per tube) Electronic Switching I/O Subsystems Meters (Watt-Hour, Water, Gas) Transportation Equipment Approvals Switching Characteristics UL 508 Recognized Component: File E69938 Pin Configuration Form-A I F 90% 10% I LOAD t t on off DS-CPC1968J-R05 www.ixysic.com 1CPC1968J INTEGRATED CIRCUITS DIVISION 1 Specifications 1.1 Absolute Maximum Ratings 25C Absolute maximum ratings are stress ratings. Stresses in Parameter Symbol Rating Unit excess of these ratings can cause permanent damage to V V Blocking Voltage 500 the device. Functional operation of the device at conditions L P beyond those indicated in the operational sections of this V Reverse Input Voltage 5V R data sheet is not implied. Input Control Current, 100 mA I Continuous F Typical values are characteristic of the device at +25C, Peak (10ms) 1 A and are the result of engineering evaluations. They are provided for information purposes only, and are not part of P 150 mW Input Power Dissipation IN the manufacturing testing requirements. Isolation Voltage (Input to Output) V 2500 V ISO rms T Operating Temperature -40 to +85 C A Storage Temperature - -40 to +125 C 1.2 Electrical Characteristics 25C Parameter Conditions Symbol Minimum Typical Maximum Units Output Characteristics 1 Load Current Peak t10ms A 25 P Continuous No Heat Sink I 2 L -- Continuous T =25C A / A C 15 rms DC T =99C Continuous I C L(99) 7.1 2 I =10mA, I =1A R On-Resistance F L - - 0.35 ON Off-State Leakage Current V =500V I L P -- 1 A LEAK Switching Speeds Turn-On t on -4.6 20 I =20mA, V =10V F L ms Turn-Off t -0.07 5 off I =0mA, V =25V, f=1MHz Output Capacitance -620 - F L C pF out I =0mA, V =1V, f=1MHz F L - 3500 - Input Characteristics 3 I =1A I Input Control Current to Activate L F -2.45 10 mA Input Control Current to Deactivate - I 0.6 - - mA F I =10mA Input Voltage Drop V F 0.9 1.35 1.56 V F V =5V Reverse Input Current I R R -- 10 A Input/Output Characteristics V =0V, f=1MHz Capacitance, Input-to-Output C IO IO -1- pF 1 Higher load currents possible with proper heat sinking. 2 Measurement taken within 1 second of on-time. 3 For applications requiring high temperature operation (T > 60C) a minimum LED drive current of 20mA is recommended. C 2 www.ixysic.com R05