CPC1988 ISOPLUS-264 Power Relay INTEGRATED CIRCUITS DIVISION Characteristics Description IXYS Integrated Circuits Division and IXYS have Parameter Rating Units combined to bring OptoMOS technology, reliability V Blocking Voltage 1000 P and compact size to a new family of high-power Solid State Relays. Load Current, T =25C: A With 5C/W Heat Sink 2.25 As part of this family, the CPC1988 single-pole A rms No Heat Sink 0.9 normally open (1-Form-A) Solid State Power Relay is rated for up to 2.25A continuous load current with a On-Resistance (max) 2.5 rms 5C/W heat sink. R JC 0.3 C/W The CPC1988 employs optically coupled MOSFET Features technology to provide 2500V of input to output rms 2.25A Load Current with 5C/W Heat Sink rms isolation. The optically coupled outputs, that use Low 2.5 On-Resistance patented OptoMOS architecture, are controlled by a 1000V Blocking Voltage highly efficient GaAIAs infrared LED. The combination P 2500V Input/Output Isolation of low on-resistance and high load current handling rms capability makes this relay suitable for a variety of high Low Thermal Resistance (0.3 C/W) performance switching applications. Electrically Non-conductive Thermal Pad for Heat Sink Applications The unique ISOPLUS-264 package pioneered by Low Drive Power Requirements IXYS enables Solid State Relays to achieve the Arc-Free With No Snubbing Circuits highest load current and power ratings. This package No EMI/RFI Generation features a unique IXYS process where the silicon Machine Insertable, Wave Solderable chips are soft soldered onto the Direct Copper Bond Applications (DCB) substrate instead of the traditional copper leadframe. The DCB ceramic, the same substrate Industrial Controls / Motor Control used in high power modules, not only provides Robotics 2500V isolation but also very low thermal Medical EquipmentPatient/Equipment Isolation rms resistance (0.3 C/W). Instrumentation Multiplexers Data Acquisition Ordering Information Electronic Switching I/O Subsystems Part Description Energy Meters CPC1988J ISOPLUS-264 Package (25 per tube) Transportation Equipment Aerospace/Defense Switching Characteristics Approvals UL 508 Certified Component: File E69938 Form-A Pin Configuration I F 90% 10% I LOAD t t 1243 on off - + e3 DS-CPC1988-R05 www.ixysic.com 1CPC1988 INTEGRATED CIRCUITS DIVISION 1 Specifications 1.1 Absolute Maximum Ratings 25C Absolute maximum ratings are stress ratings. Stresses in Symbol Ratings Units excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions Blocking Voltage 1000 V P beyond those indicated in the operational sections of this Reverse Input Voltage 5 V data sheet is not implied. Input Control Current 100 mA Peak (10ms) 1 A Input Power Dissipation 150 mW Isolation Voltage, Input to Output 2500 V rms Operational Temperature -40 to +85 C Storage Temperature -40 to +125 C 1.2 Electrical Characteristics 25C Parameter Conditions Symbol Minimum Typical Maximum Units Output Characteristics 1 Load Current Peak t10ms A 10 P Continuous No Heat Sink I 0.9 L -- T =25C Continuous A C 9.4 rms T =99C Continuous I C 1.05 L(99) 2 I =10mA, I =0.9A R On-Resistance F L -1.78 2.5 ON V =1000V Off-State Leakage Current I L P LEAK -- 1 A Switching Speeds Turn-On t -6 20 on I =20mA, V =10V ms F L Turn-Off t -0.11 5 off V =25V, f=1MHz Output Capacitance C L out -540 - pF Input Characteristics 3 I =0.9A I Input Control Current to Activate L -- 10 mA F Input Control Current to Deactivate - I 0.6 - - mA F I =5mA Input Voltage Drop V F F 0.9 1.2 1.4 V V =5V Reverse Input Current I R -- 10 A R Input/Output Characteristics Capacitance, Input-to-Output - C I/O -1- pF 1 Higher load currents possible with proper heat sinking. 2 Measurement taken within 1 second of on-time. 3 For applications requiring high temperature operation (T > 60C) a LED drive current of 20mA is recommended. C R05 www.ixysic.com 2