CPC40055ST AC Power Switch INTEGRATED CIRCUITS DIVISION Characteristics Description CPC40055ST is an AC Solid State Switch utilizing Parameter Rating Units dual power SCR outputs. This device includes V (V ) AC Operating Voltage 20-280 AC rms zero-cross turn-on circuitry and is specified with an 800V blocking voltage. Load Current P With 5C/W Heat Sink 20 A Tightly controlled zero-cross circuitry ensures low rms No Heat Sink 5 noise switching of AC loads by minimizing the V (at I =2A ) On-State Voltage Drop 1.1 P L P generation of transients. The optically coupled input and output circuits provide exceptional noise immunity V Blocking Voltage 800 P and 2500V of isolation. As a result, the rms Thermal Impedance, 0.35 C/W CPC40055ST is well suited for industrial environments Junction-to-Case, JC where electromagnetic interference would disrupt the operation of communications and control systems. Features Load Current up to 20A with 5C/W Heat Sink The unique SuperSIP package pioneered by IXYS rms Integrated Circuits allows Solid State Relays to 800V Blocking Voltage P achieve the highest load current currently available in Creepage Pin 1 to Pin 2 of 0.225 inch (5.715 mm) any similar-sized package. This package features a 5mA Control Current unique process in which the silicon chips are soft Zero-Cross Switching soldered onto the ceramic Direct Copper Bond (DCB) 2500V Isolation, Input to Output rms substrate instead of the traditional copper leadframe. Creepage Pin 2 to Pin 3 of 0.375 inch (9.525 mm) The DCB ceramic, the same substrate used in high DC Control, AC Output power modules, not only provides 2500V isolation rms Optically Isolated but also very low junction-to-case thermal impedance Low EMI and RFI Generation (0.35 C/W). High Noise Immunity Flammability Rating UL 94 V-0 Ordering Information Applications Lighting Part Description Tungsten Load: 4.75A (Free Air), 15A (Heat Sink) CPC40055ST SuperSIP Package (13 per tube) Electrical Ballast: 5A (Free Air), 15A (Heat Sink) Programmable Control Pin Configuration & Waveforms Process Control Power Control Panels Remote Switching ZC Gas Pump Electronics Contactors Large Relays 1 2 3 4 AC Load + LED LED Solenoids Motors: 1/3HP (Free Air), 1/2HP (Heat Sink) Control Heaters Approvals AC Line UL 508 Recognized Component: File E69938 See UL Approved Ratings on page 4. Load Current Voltage Across Relay DS-CPC40055ST-R04 www.ixysic.com 1CPC40055ST INTEGRATED CIRCUITS DIVISION 1 .Specifications 1.1 Absolute Maximum Ratings 25C Symbol Min Max Units Absolute maximum ratings are stress ratings. Stresses in Blocking Voltage - 800 V excess of these ratings can cause permanent damage to P the device. Functional operation of the device at conditions Reverse Input Voltage - 5 V beyond those indicated in the operational sections of this Input Control Current - 50 mA data sheet is not implied. Peak (10ms) - 1 A 1 -150 Input Power Dissipation mW Typical values are characteristic of the device at +25C, 2 -4.4 Total Power Dissipation W and are the result of engineering evaluations. They are 2 I t for Fusing provided for information purposes only, and are not part of 2 -200 A s (1/2 Sine Wave, 60Hz) the manufacturing testing requirements. Isolation Voltage, Input to Output - 2500 V 60 Seconds rms ESD, Human Body Model - 4 kV Junction Temperature (T ) -150 C J Operational Temperature - 40 +85 C Storage Temperature - 40 +125 C 1 Derate linearly 1.33mW / C. 2 Free air, no heat sink. 1.2 Electrical Characteristics 25C Parameter Conditions Symbol Minimum Typical Maximum Units Output Characteristics Load Current No Heat Sink, V =20-280V Continuous L rms 0.1 - 5 I A L rms T =25C Continuous C 0.1 - 40 Maximum Surge Current 1/2 Sine Wave, 60Hz I P -- 150 A V =800V Off-State Leakage Current I A L LEAK -- 100 P I =2A On-State Voltage Drop V L P -0.85 1.1 - P I =0mA Off-State dV/dt F dV/dt 1000 - - V/s Switching Speeds Turn-On t on -- 0.5 I =5mA cycles F Turn-Off t -- 0.5 off 1 st Zero-Cross Turn-On Voltage 1 half-cycle -6.8 20 - V subsequent half-cycle -- - 5 Holding Current - I -- 50 mA H Latching Current - I -- 75 mA L Operating Frequency - -20 - 500 Hz 2 f=60Hz Load Power Factor for Guaranteed Turn-On PF 0.25 - - - Input Characteristics 3 I =1A Resistive, f=60Hz I LED Current to Activate L -- 5 mA F Input Voltage to Deactivate - -0.8 - - V I =5mA Input Voltage Drop V F 0.9 1.2 1.5 V F V =5V Reverse Input Current I R -- 10 A R Input/Output Characteristics V =0V, f=1MHz Capacitance, Input-to-Output C IO -- 3 pF IO 1 Zero-cross first half-cycle < 100Hz. 2 Snubber circuits may be required at low power factors. 3 For high-noise environments, or high-frequency operation (>60Hz), or for applications with a high inductive load, a minimum LED drive current of 10mA is recommended. R04 www.ixysic.com 2