AMC-123SMA MACOM

AM-123 / AMC-123 High Performance Amplifier, 10 dB Gain Rev. V6 5 - 500 MHz Features FP-7 3.5 dB Mid-band Noise Figure 42 dBm Mid-band Intercept Description The AM-123 is a coupler feedback amplifier with high intercept and compression points. The use of coupler feedback minimizes noise figure and current in a high intercept amplifier. This amplifier is available in both the flat pack (FP-7) and the connectorized (C-32) packages. Due to the internal power dissipation the thermal rise is minimized. The ground plane on the PC board should be configured to remove heat from under the package. AM-123 is ideally suited for use where a high intercept, high reliability amplifier is required. C-32 Dimensions are in mm unless otherwise notedxxx = 0.010 (.xx = 0.85) .xx = 0.02 (.x = 0.5) AM-123 Positive voltage only. Weight (approx.) 0.09 ounces, 2.5 grams Pin Configuration Pin Function 1 RF OUT 2,3,6,7 GND 4,8 DC IN 5 RF IN Dimensions are in mm unless otherwise notedxxx = 0.010 (.xx = 0.85) .xx = 0.02 (.x = 0.5) Ordering Information AM-123 Positive voltage only. Weight (approx.) 1.62 ounces, 46 grams Part Number Package AM-123 PIN Flat pack (FP-7) AMC-123 SMA Connectorized (C32) 11 1 MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: AM-123 / AMC-123 High Performance Amplifier, 10 dB Gain Rev. V6 5 - 500 MHz 1,2 Electrical Specifications : T = -55C to +85C Case Temperature A Typical Guaranteed Parameter Frequency Units 25C 0 to 50C -54 to +85C* 5 - 250 MHz 9.8 9.5 9.0 Small Signal Gain (min.) dB 250 - 500 MHz 9.3 9.0 8.5 Gain Flatness (max.) 5 - 500 MHz dB 0.3 0.7 1.0 Reverse Isolation 5 - 500 MHz dB 16 Noise Figure (max.) 5 - 500 MHz dB 4.0 5.0 5.5 Power Output 1 dB comp. (min.) dBm 19.0 18.0 17.5 IP3 5 - 500 MHz dBm 34 33 IP2 5 - 500 MHz dBm 48 40 Second Order Harmonic IP 5 - 500 MHz dBm 54 5 - 500 MHz 2.1:1 / 2.1:1 2.3:1 / 2.2:1 2.5:1 / 2.4:1 VSWR In/Out Max. 20 - 400 MHz 1.6:1 / 1.8:1 2.0:1 / 2.0:1 2.2:1 / 2.2:1 DC Current 15 Volts (max.) mA 65 69 72 1. All specifications apply when operated at 15 VDC, with 50 ohms source and load impedance. 2. Heat Sinking: Operation at case temperature above 95C is not recommended. Heat sinking adequate to dissipate 1 W must be provided in use. 3,4 Absolute Maximum Ratings Handling Procedures Parameter Absolute Maximum Please observe the following precautions to avoid damage: Input Power 23 dBm V 15.75 V Static Sensitivity BIAS These electronic devices are sensitive to Operating Temperature -55C to +85C electrostatic discharge (ESD) and can be damaged by static electricity. Proper ESD control techniques Storage Temperature -65C to +125C should be used when handling these devices. 3. Exceeding any one or combination of these limits may cause permanent damage to this device. 4. MACOM does not recommend sustained operation near these survivability limits. 22 2 MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: