DS54-0002 MACOM

DS54-0002 Low Cost Four-Way SMT Power Rev. V5 Splitter/Combiner, 1700 - 2000 MHz Features Functional Block Diagram Small Size and Low Profile Industry Standard SOW-16 SMT Plastic Package Excellent Repeatability (Lot-to-Lot Variation) Typical Isolation: 18 dB Typical Amplitude Balance: 0.1 dB Low Cost Typical Insertion Loss: 1.0 dB SOW-16 Package Description M/A-COMs DS54-0002 is an IC-based monolithic power splitter/combiner in a low cost SOW-16 plastic package. This device is ideally suited for applica- tions where PCB real estate is at a premium and standard packaging for automated assembly and low cost are critical. Typical applications include infra- structure, portables and peripheral devices (PCMCIA cards) for wireless standards such as GSM, AMPS, CDPD, RAM and ARDIS. Available in tape and reel. The DS54-0002 is fabricated using a passive- integrated circuit process. The process features full- chip passivation for increased performance and reli- ability. Pin Configuration Pin No. Function Pin No. Function 1 GND 9 GND Ordering Information 2 GND 10 GND 3 RF2 (OUT) 11 GND Part Number Package 4 GND 12 RF4 (OUT) DS54-0002 Bulk Packaging 5 RF1 (OUT) 13 GND DS54-0002-TR 1000 piece reel 6 GND 14 RF3 (OUT) DS54-0002SAM Sample Test Board 7 RF IN 15 GND 8 GND 16 GND Note: Reference Application Note M513 for reel size information. 1 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions North America Tel: 800.366.2266 Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, India Tel: +91.80.4155721 China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. DS54-0002 Low Cost Four-Way SMT Power Rev. V5 Splitter/Combiner, 1700 - 2000 MHz 1 Electrical Specifications: T = 25C A Parameter Test Conditions Frequency Units Min Typ Max Insertion Loss dB 1.0 1.5 (Above 6.0 dB) Isolation 1700 - 1800 MHz dB 18 23 1801 - 2000 MHz dB 17 22 Input VSWR Ratio 1.5:1 1.7:1 Output VSWR 1700 - 1800 MHz Ratio 1.3:1 1801 - 2000 MHz Ratio 1.5:1 Amplitude Balance dB 0.1 0.7 Phase Balance Deg 4 7 1. All specifications apply with a 50-ohm source and load impedance. 2,3 Absolute Maximum Ratings Recommended PCB Configuration Parameter Absolute Maximum 4 Input Power 1W CW Operating Temperature -40C to +85C Storage Temperature -65C to +150C 2. Exceeding any one or combination of these limits may cause permanent damage to this device. 3. M/A-COM does not recommend sustained operation near these survivability limits. 4. With internal load dissipation of 0.125W maximum. Handling Procedures Please observe the following precautions to avoid damage: Static Sensitivity GMIC Circuits are sensitive to electrostatic discharge (ESD) and can be damaged by static electricity. Proper ESD control techniques should be used when handling these devices. 2 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions North America Tel: 800.366.2266 Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, India Tel: +91.80.4155721 China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice.