MAAP-010512
Amplifier, Power, 0.8 W
Rev. V4
40.5 - 43.5 GHz
Features Functional Schematic
Gain: 22 dB
P1dB: 27 dBm
High Linearity, OIP3: 38 dBm
Integrated Power Detector
Lead-Free 7 mm Laminate Package
RoHS* Compliant and 260C Reflow Compatible
Description
The MAAP-010512 is a 4-stage, high linearity 1W
power amplifier in a 7x7 mm laminate package,
allowing easy assembly. This PA product is fully
matched to 50 ohms on both the input and output. It
is designed for use as a power amplifier stage in
transmit chains and is ideally suited for 42 GHz
band point-to-point radios.
Each device is 100% RF tested to ensure
performance compliance. The part is fabricated
using an efficient pHEMT process.
1,2
Pin Configuration
Pin No. Function Pin No. Function
Ordering Information
1 RF 9 RF
IN OUT
2 V 1 10 V 3
Part Number Package G D
3 V 2 11 V 2
MAAP-010512-000000 Bulk quantity G D
4 V 3 12 V 1
G D
MAAP-010512-TR0200 200 Piece Reel
5 No Connection 13 No Connection
MAAP-010512-TR0500 500 Piece Reel
6 No Connection 14 No Connection
MAAP-010512-001SMB Sample Evaluation board
7 V 15 No Connection
REFERENCE
8 V 16 No Connection
DETECTOR
Paddle Ground
1. MACOM recommends connecting unused package pins to
ground.
2. The exposed pad centered on the package bottom must be
connected to RF and DC ground.
* Restrictions on Hazardous Substances, European Union Directive 2002/95/EC.
11
1
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
MAAP-010512
Amplifier, Power, 0.8 W
Rev. V4
40.5 - 43.5 GHz
Electrical Specifications:
Freq: 40.5 - 43.5 GHz, VD = 4 V, ID1 = 217 mA, ID2 = 300 mA, ID3 = 600 mA, T = 25C
A
Parameter Units Min. Typ. Max.
Small Signal Gain dB 18.0 22.0 27.0
Gain Flatness cross Band dB - +/-1.0 -
Input Return Loss dB - 15 -
Output Return Loss dB - 12 -
Reverse Isolation dB - 50 -
Output P1dB dBm - 27.0 -
Output IP3 dBm 32.5 38.0 -
Saturated Output Power dBm 25.0 29.0 -
Output IMD3 with Pout (scl) = 14 dBm dBc 37.0 48.0 -
3
Supply Current mA - 1117 1300
3. Adjust Vgs between 1.0 V and 0.1 V to achieve specified supply current. Typical current 1117 mA = 217 (ID1) + 300 (ID2) + 600 (ID3)
4,5,6
Absolute Maximum Ratings Handling Procedures
Please observe the following precautions to avoid
Parameter Absolute Max.
damage:
Drain Voltage +4.3 V
Gate Bias Voltage -1.5 V < Vg < 0 V
Static Sensitivity
Gallium Arsenide Integrated Circuits are sensitive
Input Power 15 dBm
to electrostatic discharge (ESD) and can be
7
Junction Temperature 150C
damaged by static electricity. Proper ESD control
Operating Temperature -40C to +85C techniques should be used when handling these
Human Body Model Class 1A devices.
Storage Temperature -55C to +150C
4. Exceeding any one or combination of these limits may cause
permanent damage to this device.
5. M/A-COM Technology Solutions does not recommend
sustained operation near these survivability limits.
6. Operating at nominal conditions with TJ 150C will ensure
6
MTTF > 1 x 10 hours.
7. Junction Temperature (T ) = T + jc * (V * I)
J C
Typical thermal resistance ( jc) = 11.2 C/W.
a) For T = 25C,
C
T = 75C @ 4 V, 1117 mA
J
b) For T = 85C,
C
T = 135C @ 4 V, 1117 mA
J
22
2
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit: