MAMX-008611 MMIC Mixer with Local Oscillator Amplifier Rev. V2 0.8 - 1.0 GHz Features Functional Schematic -5 to +5 dBm LO Drive Level High Isolation, 28 dB LO to RF Lead Free SOT-26 package Halogen-Free Green Mold Compound RF IF 1 6 260C Re-flow Compatible C1 RoHS* Compliant Version of MD57-0001 C2 C3 2 5 Description R1 The MAMX-008611 utilizes a patented floating-FET L1 mixer architecture with an on-chip LO amplifier C4 3 4 allowing it to operate with as little as 5 dBm of LO drive. This makes it an ideal choice for low power L2 portable designs. LO The MAMX-008611 is ideally suited for cellular band communications handsets that can provide only minimal amounts of LO drive. Typical applications include frequency up/down conversion and IQ modulation and demodulation in digital receivers and Pin Configuration transmitters. Pin No. Pin Name Description The MAMX-008611 is fabricated using MACOMs 0.5 micron low noise GaAs MESFET process. This 1 RF Port RF Input / Output process features full passivation for increased 2 Bias LO Amplifier Bias Resistor performance and reliability. The device is 100% RF tested to ensure superior performance specification 3 LO Port LO Input compliance. 4 V LO Amplifier V DD DD 5 GND Ground 1 6 IF Port IF Input / Output Ordering Information Part Number Package MAMX-008611-000000 SOT-26 MAMX-008611-TR3000 3000 piece reel 1. Reference Application Note M513 for reel size information. * Restrictions on Hazardous Substances, European Union Directive 2011/65/EU. 11 1 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: MAMX-008611 MMIC Mixer with Local Oscillator Amplifier Rev. V2 0.8 - 1.0 GHz 2 Electrical Specifications : T = +25C, V = 2.7 V, Typical I = 5 mA, A DD DD RF = 900 MHz (-15 dBm), LO = 730 MHz (-5 dBm), IF = 170 MHz Parameter Test Conditions Units Min. Typ. Max. Conversion Loss dB 9.3 11 LO to RF 20 28 Isolation LO to IF dB 10 12 RF to IF 20 RF Port 2.0:1 VSWR LO Port Ratio 2.0:1 IF Port 2.0:1 Input 1 dB Compression RF Freq = 900 MHz, LO = -5 dBm dBm 14 Two tones -10 dBm each Two Tone IM Ratio dBc 59 Two spacing = 1 MHz, IF = 170 MHz 2. IMR vs. RF drive can be calculated by the formula: IMR = 44 - 1.5 (PIN) 6,7,8,9 3,4 Spurious Table Absolute Maximum Ratings Parameter Absolute Maximum RF Harmonic (m) LO Harmonic (n) 5 Input RF/IF Power 27 dBm 0X 1X 2X 3X 4X 5 Input LO Power 17 dBm -10 dBm X 4.1 44.9 69.5 79.7 0X 0 dBm X 3.9 31.9 48.4 70.0 5 Operating Voltages V = 6 V DD -10 dBm 13.8 0 47.6 82.0 76.6 1X 0 dBm 22.9 0 35.1 73.0 83.8 Operating Temperature -30C to +80C -10 dBm 10.8 18.9 46.5 70.6 78.0 Storing Temperature -65C to +150C 2X 0 dBm 20.4 18.9 36.6 55.9 84.0 3. Exceeding any one or combination of these limits may cause -10 dBm 12.1 23.8 41.5 76.9 77.1 3X permanent damage to this device. 0 dBm 22.7 23.8 31.0 63.1 74.0 4. MACOM does not recommend sustained operation near these survivability limits. -10 dBm 13.6 50.9 68.5 64.5 80.6 5. Typical Thermal Resistance ( jc) = 108C/W at nominal bias. 4X 0 dBm 24.0 49.4 58.9 45.4 63.4 6. The spurious table shows the spurious signals resulting from the mixing of the RF and LO input signals assuming down conversion. 7. Mixing products are indicated relative to the IF level. 8. The lower frequency mixing term is shown for two different RF input levels. 9. The RF frequency is 900 MHz, the LO frequency is 730 MHz. nFRF - mFLO RF = -10 dBm nFRF - mFLO RF = 0 dBm 22 2 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: