600W Single Output Battery Charger PB-600 series Features : 2/3/8 stage charging (Note 4) Universal AC input / Full range Built-in active PFC function PF>0.95 Protection: Reverse polarity / Short circuit / Over voltage / Over temperature Charger for lead-acid batteries 3 color LED loading indicator Built-in remote ON-OFF control Built-in temperature compensation function Built-in fan speed control (depends on charging current) 3 years warranty SPECIFICATION MODEL PB-600-12 PB-600-24 PB-600-48 BOOST CHARGE VOLTAGE 14.4V 28.8V 57.6V FLOAT CHARGE VOLTAGE 13.8V 27.6V 55.2V RECOMMENDED BATTERY OUTPUT 135 ~ 400AH 70 ~ 210AH 35 ~ 105AH CAPACITY(AMP HOURS)(Note 3) BATTERY TYPE Open & Sealed Lead Acid OUTPUT CURRENT 40A 21A 10.5A VOLTAGE RANGE 90 ~ 264VAC 127 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) 0.95/230VAC 0.98/115VAC at full load INPUT EFFICIENCY (Typ.) 86% 87% 89% 6.8A/115VAC 3.4A/230VAC AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 25A/115VAC 50A/230VAC LEAKAGE CURRENT <3.5mA / 240VAC 16 ~ 18V 32 ~ 35V 64.5 ~ 69.5V OVER VOLTAGE PROTECTION Protection type : Shut down o/p voltage, re-power on to recover Protection type : Shut down o/p voltage, recovers automatically after temperature goes down OVER TEMPERATURE Open: Normal work Short: Stop Charging REMOTE CONTROL LEAKAGE CURRENT FROM BATTERY (Typ.) 1mA 2 / 3 / 8 stage selectable FAST CHARGE FUNCTION CHARGER OK Relay contact (RY15) OUTPUT OK Relay contact (RY13) By NTC TEMPERATURE SENSE WORKING TEMP. -20 ~ +60 (Refer toDerating Curv) 20 ~ 90% RH non-condensing WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85 , 10 ~ 95% RH TEMP. COEFFICIENT 0.05%/ (0 ~ 50 ) VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes SAFETY STANDARDS UL1012, TUV EN60335-1, EN60335-2-29 (except for 48V), EN60950-1(48V only) approved WITHSTAND VOLTAGE I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH EMC (Note 2) EMC EMISSION Compliance to EN55022 class B (CISPR22), EN61000-3-2,-3 EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024 light industry level, criteria A 135.6K hrs min. MIL-HDBK-217F (25 ) MTBF OTHERS DIMENSION 230*158*67mm(L*W*H) 2.2Kg 6pcs/14.2Kg/1.76CUFT PACKING 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. NOTE 2. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 3. This is Mean Well s suggested range. Please consult your battery manufacturer for their suggestions about maximum charging current limitation. 4. Please choose the3 stag selection when the charger is used to charge the batteries and power the loads in the same time. File Name:PB-600-SPEC 2014-09-15600W Single Output Battery Charger PB-600 series Mechanical Specification Case No.805C Unit:mm 230 145 42.5 67 7 ON/OFF SWITCH INLET Air flow 48 direction 24.1 Control Pin No. Assignment(CN100) : HRS DF11-10DP-2DS or equivalent Pin No. Assignment Pin No. Assignment Mating Housing Terminal RY13 NTC(5K ) 1,2 8 3,4 NC 9 RC- HRS DF11-10DS HRS DF11-**SC or equivalent or equivalent 5,6 RY15 10 RC+ 7 GND RY13 : Battery bank OK NTC / GND : Temperature sense RY15 : Charger OK RC+ / RC-: Remote ON/OFF Charging Curve 2 Stage 3 Stage Start Start V boost V boost V float Charge Voltage Charge Voltage 100% 100% 10% 10% Charge Current Charge Current Constant Current Constant Voltage Constant Current Constant Voltage Float stage 1 stage 2 stage 1 stage 2 stage 3 Orange Green Orange Green Color of LED Color of LED File Name:PB-600-SPEC 2014-09-15