600W Single Output With Parallel Function SCN-600 s e ri e s Features : AC input range selected by switch Protections: Short circuit / Overload / Over voltage / Over temp. High reliability/ Low ripple noise Built-in remote sense function Built-in remote ON-OFF control Built-in parallel operation function Can adjust from 20~100% output voltage by external control 1-5V Forced air cooling by built-in DC fan Case coating with paint 2 years warranty SPECIFICATION ORDER NO. SCN-600-05 SCN-600-12 SCN-600-15 SCN-600-18 SCN-600-24 SCN-600-48 SAFETY MODEL NO. 600S-N005 600S-N012 600S-N015 600S-N018 600S-N024 600S-N048 DC VOLTAGE 5V 12V 15V 18V 24V 48V RATED CURRENT 100A 50A 40A 33A 25A 12A CURRENT RANGE 0 ~ 100A 0 ~ 50A 0 ~ 40A 0 ~ 33A 0 ~ 25A 0 ~ 12A RATED POWER 500W 600W 600W 594W 600W 576W RIPPLE & NOISE (max.) Note.2 100mVp-p 120mVp-p 150mVp-p 180mVp-p 240mVp-p 480mVp-p OUTPUT VOLTAGE ADJ. RANGE 5.0% typical adjustment by potentiometer 20~100% adjustment by 1~5VDC external control VOLTAGE TOLERANCE Note.3 1.5% 1.0% 1.0% 1.0% 1.0% 1.0% LINE REGULATION 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% LOAD REGULATION 1.0% 0.5% 0.5% 0.5% 0.5% 0.5% SETUP, RISE, HOLD UP TIME 800ms, 50ms, 16ms at full load VOLTAGE RANGE 90 ~ 130VAC / 180 ~ 260VAC selected by switch, 260 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz EFFICIENCY (Typ.) 77% 80% 81% 82% 85% 87% INPUT 11A / 115VAC 7.0A / 230VAC AC CURRENT INRUSH CURRENT (max.) 60A / 230VAC LEAKAGE CURRENT 3.5mA / 240VAC 101 ~ 115% 110 ~ 135% rated output power OVERLOAD Protection type : Current limiting, delay shut down o/p voltage, re-power on to recover 110 ~ 135% follow to output set up point PROTECTION OVER VOLTAGE Protection type : Shut down o/p voltage, re-power on to recover >100 / measure by heat sink, near transformer OVER TEMPERATURE Protection type : Shut down o/p voltage, re-power on to recover -10 ~ +65 (Refer to output load derating curve) WORKING TEMP. WORKING HUMIDITY 20% ~ 90% RH non-condensing STORAGE TEMP., HUMIDITY ENVIRONMENT -20 ~ +85 , 10 ~ 95% RH TEMP. COEFFICIENT 0.04% / (0 ~ 50 ) VIBRATION 10 ~ 200Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes SAFETY STANDARDS UL60950-1, CSA22.2, IEC60950 approved WITHSTAND VOLTAGE I/P-O/P, I/P-FG:1500VAC SAFETY & I/P-O/P, I/P-FG, 100M Ohms / 500VDC / 25 / 70% RH ISOLATION RESISTANCE EMC EMI CONDUCTION & RADIATION Compliance to FCC part 15 class A (Note. 4) HARMONIC CURRENT ---- EMS IMMUNITY ---- MTBF 120Khrs min. MIL-HDBK-217F (25 ) DIMENSION 291*132*68mm (L*W*H) OTHERS PACKING 2.6kg 8pcs/ 24kg/ CARTON SPECIAL FUNCTION DC voltage adj., Remote sensing, remote control, parallel operation (refer to terminal instruction manual) 1.All parameters are specified at 230VAC input, rated load, 25 70% RH ambient. NOTE 2.Tolerence: includes set up tolerance, line regulation, load regulation. 3.Ripple & noise are measured at 20MHz by using a 12 twisted pair terminated with a 0.1uf & 47uf capacitor. 4.The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. File Name:SCN-600-SPEC 2008-05-06600W Single Output With Parallel Function SCN-600 s e ri e s Mechanical Specification Unit:mm 291 200 50.5 199.5 41 L N FG 6-32-4 AC INPUT 30 M3(NUT)x3H-4 LED V ADJ POS+ NEG- 291 250 32 9 M3(NUT)x3H-4 Air flow direction BOTTOM SIDE M6.0 Derating Curve External DC Control VS Output Voltage Vout O.V.P. 100 100 80 non-linear 60 50 40 20 V -10 0 10 20 30 40 50 60 1 2 3 4 5 Ta ( ) EXTERNAL VOLTAGE(Typical) File Name:SCN-600-SPEC 2008-05-06 LOAD (%) AC INPUT 15.5 15 OUTPUT VOLTAGE (%) DC OUTPUT NEG POS 7.5 9.5 68 115 132 VS+ VS- VCI VCO GND PAR GND INH