24FC512T-I/SM Microchip

24AA512/24LC512/24FC512 2 512K I C Serial EEPROM Device Selection Table Description: Part VCC Max. Clock Temp. The Microchip Technology Inc. 24AA512/24LC512/ Number Range Frequency Ranges 24FC512 (24XX512*) is a 64K x 8 (512 Kbit) Serial (1) Electrically Erasable PROM, capable of operation 24AA512 1.7-5.5V 400 kHz I across a broad voltage range (1.7V to 5.5V). It has 24LC512 2.5-5.5V 400 kHz I, E been developed for advanced, low-power applications (2) 24FC512 1.7-5.5V 1 MHz I such as personal communications and data acquisi- tion. This device also has a page write capability of up Note 1: 100 kHz for VCC < 2.5V to 128 bytes of data. This device is capable of both 2: 400 kHz for VCC < 2.5V random and sequential reads up to the 512K boundary. Functional address lines allow up to eight devices on Features: the same bus, for up to 4 Mbit address space. This device is available in the standard 8-pin plastic DIP, Single Supply with Operation down to 1.7V for SOIJ, SOIC, TSSOP, DFN, and 14-lead TSSOP 24AA512 and 24FC512 Devices, 2.5V for packages. The 24AA512 is also available in the 8-lead 24LC512 Devices Chip Scale package. Low-Power CMOS Technology: - Active current 400 uA, typical Block Diagram - Standby current 100 nA, typical A0 A1 A2 WP HV Generator 2 2-Wire Serial Interface, I C Compatible Cascadable for up to Eight Devices Schmitt Trigger Inputs for Noise Suppression I/O Memory EEPROM Control Control XDEC Output Slope Control to Eliminate Ground Bounce Array Logic Logic 100 kHz and 400 kHz Clock Compatibility Page Latches Page Write Time 5 ms max. Self-Timed Erase/Write Cycle SCL I/O YDEC 128-Byte Page Write Buffer Hardware Write-Protect SDA ESD Protection >4000V VCC More than 1 Million Erase/Write Cycles Sense Amp. VSS Data Retention > 200 years R/W Control Packages Include 8-lead PDIP, SOIJ, SOIC, TSSOP, DFN, Chip Scale and 14-lead TSSOP Pb-Free and RoHS Compliant Temperature Ranges: - Industrial (I): -40 C to +85 C - Automotive (E):-40 C to +125 C Package Type (1) PDIP/SOIJ/SOIC/TSSOP DFN TSSOP CS (Chip Scale) VCC A1 A0 1 14 VCC A0 1 8 VCC A0 1 A0 8 VCC 2 13 WP 1 2 3 A1 2 A1 2 7 WP 3 A1 7 WP 12 WP 45 A2 NC NC 4 11 NC NC 3 8 A2 6 SCL 6 7 A2 3 6 SCL 5 10 NC NC SDA SCL VSS 4 VSS 5 SDA 9 6 VSS 4 5 SDA A2 SCL (TOP DOWN VIEW, 7 8 BALLS NOT VISIBLE) VSS SDA Note 1: Available in I-temp, AA only. * 24XX512 is used in this document as a generic part number for the 24AA512/24LC512/24FC512 devices. 2010 Microchip Technology Inc. DS21754M-page 1 24XX512 24XX512 24XX51224AA512/24LC512/24FC512 1.0 ELECTRICAL CHARACTERISTICS () Absolute Maximum Ratings VCC.............................................................................................................................................................................6.5V All inputs and outputs w.r.t. VSS ......................................................................................................... -0.6V to VCC +1.0V Storage temperature ...............................................................................................................................-65C to +150C Ambient temperature with power applied................................................................................................-40C to +125C ESD protection on all pins 4kV NOTICE: Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. TABLE 1-1: DC CHARACTERISTICS Electrical Characteristics: DC CHARACTERISTICS Industrial (I): VCC = +1.7V to 5.5V TA = -40C to +85C Automotive (E): VCC = +2.5V to 5.5V TA = -40C to +125C Param. Sym. Characteristic Min. Max. Units Conditions No. D1 A0, A1, A2, SCL, SDA and WP pins: D2 VIH High-level input voltage 0.7 VCC V D3 VIL Low-level input voltage 0.3 VCC V VCC 2.5V 0.2 VCC V VCC < 2.5V D4 VHYS Hysteresis of Schmitt 0.05 VCC VVCC 2.5V (Note) Trigger inputs (SDA, SCL pins) D5 VOL Low-level output voltage 0.40 V IOL = 3.0 ma VCC = 4.5V IOL = 2.1 ma VCC = 2.5V D6 ILI Input leakage current 1 AVIN = VSS or VCC, WP = VSS VIN = VSS or VCC, WP = VCC D7 ILO Output leakage current 1 AVOUT = VSS or VCC D8 CIN, Pin capacitance 10 pFVCC = 5.0V (Note) COUT (all inputs/outputs) TA = 25C, FCLK = 1 MHz D9 ICC Read Operating current 400 AVCC = 5.5V, SCL = 400 kHz ICC Write 5 mA VCC = 5.5V D10 ICCS Standby current 1 ATA = -40C to +85C SCL = SDA = VCC = 5.5V A0, A1, A2, WP = VSS 5 ATA = -40C to +125C SCL = SDA = VCC = 5.5V A0, A1, A2, WP = VSS Note: This parameter is periodically sampled and not 100% tested. DS21754M-page 2 2010 Microchip Technology Inc.