SFM11PL MCC TM omponents THRU 20736 Marilla Street Chatsworth Micro Commercial Components SFM18PL Features x For Surface Mount Applications x Low Power Loss, High Efficiency 1 Amp Super Fast x High Temp Soldering: 260Cq for 10 Seconds At Terminals Halogen free available upon request by adding suffix-H Recovery Epoxy meets UL 94 V-0 flammability rating Silicon Rectifier Moisture Sensitivity Level 1 x Lead Free Finish/RoHS Compliant (Note1)Suffix designates 50 to 600 Volts Compliant. See ordering information) o x Welding Iron Temp:350 C for 3s max. o x Storage Condition: Less than 30 C,RH<70% Maximum Ratings SOD-123FL x Operating Temperature: -50 q C to +150 q C A x Storage Temperature: -50q C to +150 q C x Maximum Thermal Resistance 75 q C/W Junction To Ambient. B MCC Maximum Maximum Maximum Part Device Recurrent RMS DC C E Number Marking Peak Reverse Voltage Blocking Voltage Voltage SFM11PL S1 50V 35V 50V SFM12PL S2 100V 70V 100V SFM13PL S3 150V 105V 150V H D SFM14PL S4 200V 140V 200V SFM15PL S5 300V 210V 300V SFM16PL S6 400V 280V 400V SFM17PL S7 500V 350V 500V G SFM18PL S8 600V 420V 600V DIMENSIONS DIM INCHES MM NOTE Electrical Characteristics 25q C Unless Otherwise Specified MIN MAX MIN MAX Average Forward I 1.0A T = 50 q C F(AV) a A .140 .152 3.55 3.85 Current B .100 .122 2.55 3.10 Peak Forward Surge I 30A 8.3ms, half sine FSM C .055 .075 1.40 1.90 Current D .035 .053 0.90 1.35 Maximum E .020 .041 0.50 1.05 Instantaneous G .010 ----- 0.25 ----- Forward Voltage H ----- .010 ---- .25 SFM11PL-14PL V .95V I = 1.0A F FM SFM15PL-16PL 1.25V T = 25 q C a SUGGESTED SOLDER SFM17PL-18PL 1.70V PAD LAYOUT Maximum DC 0.093 Reverse Current At I 5P A Ta = 25 q C R Rated DC Blocking 100 P A Ta = 100 q C Voltage Maximum Reverse I =0.5A, I =1.0A, F R 0.048 Recovery Time T 35ns I =0.25A rr rr Typical Junction Measured at C 10pF J 0.036 Capacitance 1.0MHz, V =4.0V R Note: 1. High Temperature Solder Exemption Applied, see EU Directive Annex 7. www.mccsemi.com Revision: C 2013/01 of 3 1/01MCC SFM11PL THRU SFM18PL TM Micro Commercial Components RATING AND CHARACTERISTIC CURVES FIG.2-TYPICAL FORWARD CURRENT FIG.1-TYPICAL FORWARD DERATING CURVE CHARACTERISTICS 10 1.2 1.0 0.8 1.0 Single Phase 0.6 Half Wave 60Hz Resistive Or Inductive Load 0.4 0.2 .1 0 0 25 50 75 100 125 150 175 AMBIENT TEMPERATURE ( C) Tj=25 C .01 FIG.4-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 30 .001 1.6 1.8 .4 .6 .8 1.0 1.2 1.4 24 FORWARD VOLTAGE,(V) FIG.3- TEST CIRCUIT DIAGRAM AND REVERSE 18 8.3ms Single Half Tj=25 C RECOVERY TIME CHARACTERISTICS Sine Wave 12 50 10 NONINDUCTIVE NONINDUCTIVE JEDEC method 6 (+) ( ) D.U.T. 25Vdc PULSE 0 (approx.) GENERATOR 1150 50 100 (NOTE 2) ( ) (+) 1 NUMBER OF CYCLES AT 60Hz OSCILLISCOPE NON- (NOTE 1) INDUCTIVE NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. 2. Rise Time= 10ns max., Source Impedance= 50 ohms. FIG.5-TYPICAL JUNCTION CAPACITANCE 70 trr 60 +0.5A 50 0 40 -0.25A 30 20 -1.0A 10 1cm SET TIME BASE FOR 0 .01 .05 .1 .5 1 5 10 50 100 50 / 10ns / cm REVERSE VOLTAGE,(V) www.mccsemi.com Revision: C 2 of 3 2013/01/01 SFM15~SFM16 SFM17~SFM18 SFM11~SFM14 INSTANTANEOUS FORWARD CURRENT,(A) JUNCTION CAPACITANCE,(pF) PEAK FORWARD SURGE CURRENT,(A) AVERAGE FORWARD CURRENT,(A)