MIKROE-1874 MikroElektronika

2. Soldering the headers Before using your click board, make sure to solder 1x8 male headers to both left and right side of the board. Two 1x8 male headers are included with the board in the package. 1 EXPAND 3 click 2 3 4. Essential features Each DS2408 IC has a factory-lasered 64-bit registration number. Combined with the standard Dallas Semiconductor 1-Wire protocol it uses to communicate with the target board MCU, the registration number enables multiple devices to reside on the Turn the board upside down so that Turn the board upward again. Make sure same data line, each one with a unique ID. the bottom side is facing you upwards. to align the headers so that they are To connect multiple Expand 3 clicks , use Place shorter pins of the header into the perpendicular to the board, then solder the the additional three pins positioned above appropriate soldering pads. pins carefully. the mikroBUS socket (VCC, OW, GND). 1. Introduction EXPAND 3 click is an accessory board in mikroBUS form factor. It includes an 3. Plugging the board in 8-channel programmable I/O expander click DS2408 that communicates with the target Once you have soldered the headers your board MCU through a 1-Wire interface (15.3 board is ready to be placed into the desired BOARD kbps or 100kbps) The onboard GP SEL jumper mikroBUS socket. Make sure to align the www.mikroe.com allows you to specify the communication pins cut in the lower-right part of the board with (either OW1 or OW0, which are in place of the the markings on the silkscreen at the usual AN and PWM pins on mikroBUS ). An mikroBUS socket. If all the EXPAND 3 click manual ver 1.00 additional reset line (RST) is also connected. pins are aligned correctly, The board is designed to use either a 3.3V or push the board all the way 5V power supply. into the socket. 01000000773448. Code examples 5. Schematic VCC VCC VCC-3.3V VCC-5V Once you have done all the necessary preparations, its time to get your click board C1 OW1 OW0 AN PWM 100nF RST up and running. We have provided examples RST INT CS TX for mikroC , mikroBasic and mikroPascal SCK RX R2 U1 MISO SCL compilers on our Libstock website. Just 2K2 1 16 SDA MOSI NC NC download them and you are ready to start. +3.3V +5V P0 2 15 GND GND P0 NC MIKROBUS DEVICE CONN. 3 14 P1 VCC P1 OW 4 13 P2 I/O P2 .com 5 12 P3 GND P3 J1 J2 6 11 1 1 P4 OW0 NC P4 VCC-3.3V P7 7 10 RST OW 2 VCC 2 P7 RST 9. Support P6 8 9 P5 OW1 3 3 P6 P5 VCC-5V GP SEL VCC SEL. DS2408 MikroElektronika offers free tech support (www.mikroe.com/support) until the end of the products lifetime, so if something goes VCC HD1 VCC VCC P0 1 2 P1 P2 3 4 P3 wrong, were ready and willing to help HD2 R1 P4 5 6 P5 1 2K2 7 8 P6 P7 OW 2 9 10 3 N2X5 N1X3 PWR 6. Dimensions 7. SMD Jumper 10. Disclaimer MikroElektronika assumes no responsibility mm mils or liability for any errors or inaccuracies that may appear in the present document. LENGTH 42.9 1690 Specification and information contained in WIDTH 25.4 1000 the present schematic are subject to change HEIGHT* 3.3 130 The board features a VCC SEL. Jumper (zero at any time without notice. ohm resistor) that allows you to choose 42.9 mm / 1690 mils * without headers between a 3.3V or 5V power supply. By Copyright 2015 MikroElektronika. default its soldered in the 3.3V position. All rights reserved. 25.4 mm / 1000 mils