MIKROE-1887 MikroElektronika

2. Soldering the headers Before using your click board, make sure to solder 1x8 male headers to both left and right side of the board. Two 1x8 male headers are included with the board in the package. 1 4. Essential features GNSS click 2 3 The L76 module on GNSS2 click integrates performance-enhancing Quectel technologies. It can automatically predict satellite orbits from data stored in its internal flash (EASY technology) and it can adaptively adjust its on/off time to balance between positioning accuracy and power consumption (AlwaysLocate technology). GNSS2 click Turn the board upside down so that Turn the board upward again. Make sure also features a VBAT connector for connecting the bottom side is facing you upwards. to align the headers so that they are an external power supply which can supply Place shorter pins of the header into the perpendicular to the board, then solder the power to the modules SRAM memory (storing appropriate soldering pads. pins carefully. GPS information necessary for quick start-up). 1. Introduction GNSS2 click carries Quectels L76 module 3. Plugging the board in and an SMA antenna connector. L76 can click acquire both GPS and GLONASS signals. The Once you have soldered the headers your larger number of visible satellites increases board is ready to be placed into the desired BOARD positioning accuracy (<2.5m CEP) and mikroBUS socket. Make sure to align the www.mikroe.com decreases acquisition time (<5s TTFF with cut in the lower-right part of the board with warm start). GNSS2 click communicates the markings on the silkscreen at the with the target board MCU through UART mikroBUS socket. If all the GNSS2 click manual ver 1.00 (RX, TX) pins as well as Force on (AN), RST pins are aligned correctly, (RST), Standby (PWM). The board can use push the board all the way either 3.3 or 5V power supply and logic levels. into the socket. 01000000783418. Code examples 5. Schematic Once you have done all the necessary preparations, its time to get your click board up and running. We have provided examples CN1 ANTENNA Vgps VCC Vgps C3 for mikroC , mikroBasic and mikroPascal 4.7uF Vgps D1 U1 1 5 Schottky compilers on our Libstock website. Just T RST IN OUT 10 9 2 R2 GND R6 RFIN 249K download them and you are ready to start. 11 8 3 4 2K2 EN ADJ 12 7 AP7331-ADJ R3 VBCKP C2 22K 13 6 2.2uF R4 L1 R7 Quectel VCCRF T STANDBY 14 5 C5 C9 12K1 47nH 10 L76 1PPS 15 4 100nF 4.7uF .com C7 C6 22nF 4.7uF T RXD 16 3 VCC VCC-5V VCC-3.3V T TXD 17 2 T FORCE ON 18 1 C1 R1 E1 PWR SEL.A Vgps Vgps Vgps 100nF 10uF 2K2 9. Support PWR C4 E2 R8 2K2 Vgps 100nF 10uF VCC VCC-3.3V VCC-5V PPS Q1 R5 PDTC114EU MikroElektronika offers free tech support 10K U2 R1 1PPS T STANDBY 1 16 STANDBY FORCE ON STANDBY A1 B1 AN PWM 2 15 RST (www.mikroe.com/support) until the end of VCCA VCCB RST INT T RST 3 14 RST TX R2 A2 B2 CS TX T RXD 4 13 RX RX A3 B3 SCK RX the products lifetime, so if something goes T TXD 5 12 TX A4 B4 SCL MISO T FORCE ON 6 11 FORCE ON A5 B5 MOSI SDA 7 10 A6 B6 +3.3V +5V wrong, were ready and willing to help 8 9 GND OE GND GND GND R9 10K C8 TXB0106 MIKROBUS DEVICE CONN. 100nF 6. Dimensions 7. SMD jumper 10. Disclaimer MikroElektronika assumes no responsibility mm mils or liability for any errors or inaccuracies that may appear in the present document. PCB LENGTH 57.15 2250 Specification and information contained in FULL LENGTH 65 2560 the present schematic are subject to change WIDTH 25.4 1000 GNSS2 click features a PWR SEL jumper at any time without notice. (zero ohm resistor), that switches both the 57.15 mm / 2250 mils HEIGHT* 8 315 power supply and logic level between 3.3V Copyright 2015 MikroElektronika. 65 mm / 2560 mils * without headers and 5V. All rights reserved. 25.4 mm / 1000 mils TXB0106