DLP0QSA150HL2D Murata

Reference Only Spec No. JEFL243E-0019E-01 P1/9 Chip Common Mode Choke Coil DLP0QSAHL2 Reference Specification 1. Scope This reference specification applies to Chip Common Mode Choke Coil DLP0QSA Series. 2. Part Numbering (ex.) DL P 0Q S A 350 H L 2 D (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (1) Chip Common Mode Choke Coil (6) Impedance (Typ. at 100MHz) (2) Structure (P : Film Type) (7) Circuit H : Characteristic Impedance 100 system (3) Dimension (LW : 0.650.50mm) (8) Features (4) Type (9) Number of Line (5) Category: Cut off Frequency 6GHz(Typ.) (10) Packaging Code D : Taping / B : Bulk 3. Rating Common Mode Impedance Customer Murata Rated Withstanding Rated DC Insulation (at 100MHz, Under Part Number Part Number Voltage Voltage Current Resistance Resistance Standard Testing Condition) DLP0QSA350HL2D 3510 2.225% DLP0QSA350HL2B DLP0QSA150HL2D 100M 155 0.85V(DC) 12.5V(DC) 100mA 25% min. DLP0QSA150HL2B DLP0QSA070HL2D 72 0.725% DLP0QSA070HL2B Operating Temperature : -40 to +85C Storage Temperature : -40 to +85C 4. Standard Testing Conditions <Unless otherwise specified> <In case of doubt> Temperature : Ordinary Temperature 15 to 35C Temperature : 20 2C Humidity : Ordinary Humidity 25 to 85%(RH) Humidity : 60 to 70%(RH) Atmospheric Pressure : 86 to106kPa 5.Style and Dimensions Equivalent Circuits (1) (2) (Top View) (1) (2) (4) (3) 0.20 0.10 (4) (3) No polarity. (Side View) Unit Mass(Typical value) 0.5mg :Electrode (Bot tom View) (in : mm) 0.15 0.07 0.50 0.05 6.Marking No Marking. MURATA MFG.CO.,LTD 0.65 0.05 (0.40) 0.30 0.05Reference Only Spec No. JEFL243E-0019E-01 P2/9 7. Electrical Performance No. Item Specification Test Method 7.1 Common Mode Meet item 3. Measuring Frequency : 1001MHz (ref.item 10.) Impedance Measuring Equipment : KEYSIGHT HP4991A or the equivalents (In case of doubt in standard condition, the heat treatment(200C, about 10 minutes)shall be applied. 7.2 Withstanding Products shall not be damaged. Test Voltage : 2.5 times for Rated Voltage Voltage Time : 1 to 5 seconds Charge Current : 1 mA max.(ref.item 10.) 7.3 DC Resistance Meet item 3. Measuring current : 50mA max.(ref.item 10.) (Rdc) 7.4 Insulation Measuring voltage : Rated Voltage Resistance (I.R.) Measuring time : 1 minute max. (ref.item 10.) 8.Mechanical Performance No. Item Specification Test Method 8.1 Appearance and Meet item 5. Visual Inspection and measured with Slide Calipers. Dimensions 8.2 Solderability The electrodes shall be at least Flux : Ethanol solution of rosin,25(wt)% 95% covered with new solder Pre-Heating : 15010C, 6090s coating. Solder : Sn-3.0Ag-0.5Cu Solder Temperature : 2403C Immersion Time : 30.5s Immersion and emersion rates : 25 mm / s 8.3 Resistance to Meet Table 1. Flux : Ethanol solution of rosin,25(wt)% Soldering Heat Table 1 Pre-Heating : 15010C, 6090s Solder : Sn-3.0Ag-0.5Cu Appearance No damaged Solder Temperature : 2705C Common Mode Immersion Time : 51s Impedance within 20% Immersion and emersion rates : 25 mm / s Change Then measured arter exposure in the room condition 100M min. I.R. for 4 to 48 hours. 8.4 Drop It shall be dropped on concrete or steel board. DC Resistance within 30% Method : free fall Change Height : 1m The Number of Times : 10 times 8.5 Vibration It shall be soldered on the substrate. Oscillation Frequency : 10 to 2000 to 10Hz for 15 minutes Total amplitude : 3.0 mm or Acceleration amplitude 2 196 m/s whichever is smaller. Testing Time : A period of 2 hours in each of 3 mutually perpendicular directions. 8.6 Bending Meet Table 2. Substrate : Glass-epoxy substrate (t=1.0mm). Strength Table 2 Deflection : 3 mm Speed of Applying Force : 1.0 mm / s Appearance No damaged Keeping time : 5 seconds DC Resistance within 30% Pressure jig Change R230 F Deflection 45 45 Product MURATA MFG.CO.,LTD