Chip Monolithic Ceramic Capacitor for Automotive limited to Conductive Glue Mounting GCG32EC71E226KE01 (1210, X7S:EIA, 22uF, DC25V) : packaging code Reference Sheet 1.Scope This product specification is applied to Chip Monolithic Ceramic Capacitor limited to Conductive Glue Mounting Type used for Automotive Electronic equipment with conductive glue mounting. 2.MURATA Part NO. System (Ex.) GCG 32 E C7 1E 226 K E01 L (1)L/W (2)T (3)Temperature (4)Rated (5)Nominal (6)Capacitance (7)Muratas Control (8)Packaging Code Dimensions Dimensions Characteristics Voltage Capacitance Tolerance Code 3. Type & Dimensions (Unit:mm) (1)-1 L (1)-2 W (2) T e g 3.20.4 2.50.3 2.50.3 0.3 min. 1.0 min. 4.Rated value (3) Temperature Characteristics Specifications and Test (4) (6) (Public STD Code):X7S(EIA) (5) Nominal Methods Rated Capacitance Capacitance (Operating Temp. coeff Temp. Range Voltage Tolerance Temp. Range) orCap. Change (Ref.Temp.) -55 to 125 C -22 to 22 % DC 25 V 22 uF 10 % -55 to 125 C (25 C) 5.Package mark (8) Packaging Packaging Unit f180mm Reel L 1000 pcs./Reel EMBOSSED W8P4 f330mm Reel K 4000 pcs./Reel EMBOSSED W8P4 Product specifications in this catalog are as of Apr.14,2016,and are subject to change or obsolescence without notice. Please consult the approval sheet before ordering. Please read rating and Cautions first. GCG32EC71E226KE01-01 1AEC-Q200 Murata Standard Specification and Test Methods No AEC-Q200 Test Item Specification. AEC-Q200 Test Method Pre-and Post-Stress 1 - Electrical Test 2 High Temperature The measured and observed characteristics should satisfy the Fix the capacitor to the supporting jig in the same manner and Exposure (Storage) specifications in the following table. under the same conditions as No.16. Appearance No marking defects Set the capacitor for 100012 hours at 1503 . Set for Capacitance C7: Within 12.5 242 hours at room temperature, then measure. Change Dissipation C7: 0.2max Factor Insulation More than 2,000M or 50 F Resistance (Whichever is smaller) 3 Temperature Cycling The measured and observed characteristics should satisfy the Fix the capacitor to the supporting jig in the same manner and under specifications in the following table. the same conditions as No.16.Perform the 1000 cycles test according to Appearance No marking defects the four heat treatments listed in the following table. Set for 242 hours at Capacitance C7: Within 10.0% room temperature, then measure Change Step 1 2 3 4 Dissipation C7: 0.1max Factor Temp. Room Room -55+0/-3 125+3/-0 ( C) Temp. Temp. Time 15 3 1 15 3 1 Insulation 100 F min. (min.) Resistance Initial measurement for high dielectric constant type Perform a heat treatment at 150+0/-10 for one hour and then set for 242 hours at room temperature. Perform the initial measurement. 4 Destructive No defects or abnormalities Per EIA-469 Physical Analysis 5 Moisture Resistance The measured and observed characteristics should satisfy the Fix the capacitor to the supporting jig in the same manner and under the same conditions as No.16. specifications in the following table. Apply the 24-hour heat (25 to 65 ) and humidity (80 to 98%) Appearance No marking defects treatment shown below, 10 consecutive times. Set for 242 hours at room temperature, then measure. Capacitance C7: Within 12.5% Change Humidity Humidity Temperature 8098% 80 98% Humidity Humidity Humidity Dissipation C7: 0.2max () 9098% 9098% 9098% 70 Factor 65 60 55 50 45 40 35 30 25 Insulation More than 2,000M or 50 F +10 20 - 2 Resistance (Whichever is smaller) 15 10 5 Initial measuremt 0 -5 -10 One cycle 24hours 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Hours Measurement after test for high dielectric constant type Perform a heat treatment at 150+0/10C for one hour and then let sit for 242 hours at room temperature, then measure. 6 The measured and observed characteristics should satisfy the Fix the capacitor to the supporting jig in the same manner and Biased Humidity specifications in the following table. under the same conditions as No.16. Apply the rated voltage and 1.3+0.2/-0vdc (add 6.8k resister) Appearance No marking defects at 853 and 80 to 85% humidity for 100012 hours. Capacitance C7: Within 12.5% Remove and set for 242 hours at room temperature, then measure. Change The charge/discharge current is less than 50mA. Dissipation C7: 0.2 max Factor Measurement after test for high dielectric constant type Perform a heat treatment at 150+0/10C for one hour and then let Insulation More than 1,000M or 25 F sit for 242 hours at room temperature, then measure. Resistance (Whichever is smaller) JEMCGS-04728 2