LPC11E3x 32-bit ARM Cortex-M0 microcontroller up to 128 kB flash up to 12 kB SRAM and 4 kB EEPROM USART Rev. 2.3 11 September 2014 Product data sheet 1. General description The LPC11E3x are an ARM Cortex-M0 based, low-cost 32-bit MCU, designed for 8/16-bit microcontroller applications, offering performance, low power, simple instruction set and memory addressing together with reduced code size compared to existing 8/16-bit architectures. The LPC11E3x operate at CPU frequencies of up to 50 MHz. The peripheral complement of the LPC11E3x includes up to 128 kB of flash memory, up to 2 12 kB of SRAM data memory and 4 kB EEPROM, one Fast-mode Plus I C-bus interface, one RS-485/EIA-485 USART with support for synchronous mode and smart card interface, two SSP interfaces, four general purpose counter/timers, a 10-bit ADC, and up to 54 general purpose I/O pins. The I/O Handler is a software library-supported hardware engine that can be used to add performance, connectivity and flexibility to system designs. It is available on the LPC11E37HFBD64/401. The I/O Handler can emulate serial interfaces such as UART, 2 2 I C, and I S with no or very low additional CPU load and can off-load the CPU by performing processing-intensive functions like DMA transfers in hardware. Software libraries for multiple I/O Handler applications are available on LPC11E3x NXP Semiconductors 32-bit ARM Cortex-M0 microcontroller Debug options: Standard JTAG (Joint Test Action Group) test interface for BSDL (Boundary Scan Description Language). Serial Wire Debug. Digital peripherals: Up to 54 General Purpose I/O (GPIO) pins with configurable pull-up/pull-down resistors, repeater mode, and open-drain mode. Up to 8 GPIO pins can be selected as edge and level sensitive interrupt sources. Two GPIO grouped interrupt modules enable an interrupt based on a programmable pattern of input states of a group of GPIO pins. High-current source output driver (20 mA) on one pin. High-current sink driver (20 mA) on true open-drain pins. Four general purpose counter/timers with a total of up to 8 capture inputs and 13 match outputs. Programmable Windowed WatchDog Timer (WWDT) with a dedicated, internal low-power WatchDog Oscillator (WDO). Analog peripherals: 10-bit ADC with input multiplexing among eight pins. Serial interfaces: USART with fractional baud rate generation, internal FIFO, a full modem control handshake interface, and support for RS-485/9-bit mode and synchronous mode. USART supports an asynchronous smart card interface (ISO 7816-3). Two SSP controllers with FIFO and multi-protocol capabilities. 2 2 I C-bus interface supporting the full I C-bus specification and Fast-mode Plus with a data rate of up to 1 Mbit/s with multiple address recognition and monitor mode. I/O Handler for hardware emulation of serial interfaces and DMA supported through software libraries.(LPC11E37HFBD64/401 only.) Clock generation: Crystal Oscillator with an operating range of 1 MHz to 25 MHz (system oscillator). 12 MHz high-frequency Internal RC oscillator (IRC) that can optionally be used as a system clock. Internal low-power, low-frequency WatchDog Oscillator (WDO) with programmable frequency output. PLL allows CPU operation up to the maximum CPU rate with the system oscillator or the IRC as clock sources. Clock output function with divider that can reflect the crystal oscillator, the main clock, the IRC, or the watchdog oscillator. Power control: Integrated PMU (Power Management Unit) to minimize power consumption during Sleep, Deep-sleep, Power-down, and Deep power-down modes. Power profiles residing in boot ROM provide optimized performance and minimized power consumption for any given application through one simple function call. Four reduced power modes: Sleep, Deep-sleep, Power-down, and Deep power-down. Processor wake-up from Deep-sleep and Power-down modes via reset, selectable GPIO pins, or the watchdog interrupt. Processor wake-up from Deep power-down mode using one special function pin. LPC11E3X All information provided in this document is subject to legal disclaimers. NXP Semiconductors N.V. 2014. All rights reserved. Product data sheet Rev. 2.3 11 September 2014 2 of 71