QorIQ LS Processor Family QorIQ LS1012A Reference Design Board The QorIQ LS1012A Reference Design Board is a compact form factor tool that enables evaluation and software development for a broad range of applications. OVERVIEW The LS1012A processor is a cost-effective, power-efficient and highly integrated system-on-chip design that extends The QorIQ LS1012A communications processor addresses a the reach of NXPs Value Performance line of QorIQ wide variety of applications such as consumer NAS, battery- communications processors into the ultra-value tier. Featuring powered mobile NAS, entry-level broadband gateway, value- an extremely power-efficient 64-bit ARM Cortex -A53 core tier IoT gateways, trusted gateways, Industrial automation, core running at up to 800 MHz and yielding over 2,000 building control, networked audio, Ethernet drives and more. CoreMarks, the LS1012A will deliver high packet processing The QorIQ LS1012A reference design board (LS1012ARDB) performance and low power consumption. is a compact form-factor tool that enables evaluation of the LS1012A solution for these and other low-end networking Additional functionally includes an integrated hardware packet applications. The LS1012ARDB also features an expansion acceleration engine, together with high-speed interfaces connector suitable for adding additional components such as and support for DDR3L running at 1000 MHz. High-speed Arduino shields. peripherals include PCIe Gen2, Super Speed USB3.0, USB2.0, SATA3.0 and dual Gigabit Ethernet controllers, with The QorIQ LS1012ARDB can help shorten your time-to-market support for RGMII, and SGMII that can accommodate 2.5 Gbit by exercising most capabilities of the device and can serve as Ethernet PHYs. To deliver outstanding security performance, a reference for hardware development. It can also be used as the LS1012A features a hardware-based acceleration engine a debug tool to check behaviors on the board compared to to support Secure Boot, and networking with both ARM behaviors seen on customer boards. The board can be used TrustZone and NXPs QorIQ Trust Architecture. for software development and performance evaluation prior to the customers own board being ready. The LS1012ARDB comes in a compact 5.59 in x 5.59 in form factor which allows mounting in an enclosure. An SDIO Wi-Fi module is included to facilitate evaluation and development of Wi-Fi connectivity solutions.FEATURES QorIQ LS1012ARDB SYSTEM BLOCK DIAGRAM MEMORY USB 2.0 & 3.0 USB Connector 1GB DDR3L SDRAM SDHC2 SGMI GbE 4 GB eMMC Memory GbE PHY 4 GB eMMC Memory SDHC Card Slot SATA3 SATA 128 MB QSPI NOR Flash SDIO Wi-Fi Module PCIe Half-Height LS1012A Bank064MB mPCIe Connector Arduino PC1 Bank164MB QuadSPI 128 MB Shield Header NOR Flash SA12 ETHERNET DDR3L 1 GB DDR3L RGMII SDRAM GbE 2 x GbE LAN connectors GbE PHY 1 x PoE enable port VR5100 USB to JTAG K22 PMIC USB 1 x USB 3.0 micro AB port OTHER NXP DEVICES ON BOARD: NTSX2102 dual-supply translating 1 x SDIO Wi-Fi module 2.4 GHz transceiver LS1012A communications processor 802.11b/g/n 74CBTLV3253 Dual 1 of 4 multiplexer/ VR5100 multi-output DC-DC regulator 1 x half-height Mini PCI Express demultiplexer K22 OpenSDA serial and debugger connector NX5P2190 logic-controlled high-side adapter 1 x USB to JTAG using NXPs K22 power switch FXAS21002 3-Axis digital angular rate 1 x SATA connector CBTL02043A 2:1 multiplexer/ gyroscope demultiplexer 1 x 3-Axis digital angular rate gyroscope FXOS8700CQ 6-axis sensor with MC34713 5.0 A 1.0 MHz single switch- accelerometer and magnetometer 1 x 6-axis sensor mode power supply BC3770 2.0 A switch-mode charger 1 x Arduino shield header for expansion QorIQ LS1012A DEVELOPMENT BOARD www.nxp.com NXP, the NXP logo, Layerscape and QorIQNXP, the NXP logo, Layerscape and QorIQ are trademarks of NXP B.V. ARM, Cortex and TrustZone are registered trademarks of ARM Limited (or its subsidiaries) in the EU and/or elsewhere. All rights reserved. 2014, 2016 NXP B.V. Document Number: LS1012ARDBFS REV 0 Date of release: May 2016.