Freescale Semiconductor Document Number: MC9S08JE128 Rev. 3, 04/2010 Data Sheet: Advanced Information An Energy-Efficient Solution from Freescale MC9S08JE128 series Covers: MC9S08JE128 and MC9S08JE64 64-LQFP 10mm x 10mm 80-LQFP 12mm x 12mm 81-MapBGA 10mm x10mm byte-by-byte data transfer supports broadcast mode and 11-bit 8-Bit HCS08 Central Processor Unit (CPU) addressing Up to 48-MHz CPU above 2.4 V, 40 MHz CPU above 2.1 V, and PRACMP Analog comparator with selectable interrupt 20 MHz CPU above 1.8 V across temperature of -40C to 105C compare option to programmable internal reference voltage HCS08 instruction set with added BGND instruction operation in stop3 Support for up to 32 interrupt/reset sources SCI Two serial communications interfaces with optional 13-bit On-Chip Memory break option to connect Rx input to PRACMP output on SCI1 and 128 K Dual Array Flash read/program/erase over full operating SCI2 High current drive on Tx on SCI1 and SCI2 wake-up from voltage and temperature stop3 on Rx edge 12 KB Random-access memory (RAM) SPI1 Serial peripheral interface (SPI) with 64-bit FIFO buffer Security circuitry to prevent unauthorized access to RAM and 16-bit or 8-bit data transfers full-duplex or single-wire Flash bidirectional double-buffered transmit and receive master or Power-Saving Modes slave mode MSB-first or LSB-first shifting Two ultra-low power stop modes. Peripheral clock enable register SPI2 Serial peripheral interface with full-duplex or single-wire can disable clocks to unused modules to reduce currents bidirectional Double-buffered transmit and receive Master or Time of Day (TOD) Ultra-low power 1/4 sec counter with up to Slave mode MSB-first or LSB-first shifting 64s timeout. TPM Two 4-channel Timer/PWM Module Selectable input Ultra-low power external oscillator that can be used in stop modes capture, output compare, or buffered edge- or center-aligned to provide accurate clock source to the TOD. 6 usec typical wake PWM on each channel external clock input/pulse accumulator up time from stop3 mode USB Supports USB in full-speed device configuration. On-chip Clock Source Options transceiver and 3.3V regulator help save system cost, fully Oscillator (XOSC1) Loop-control Pierce oscillator 32.768 kHz compliant with USB Specification 2.0. Allows control, bulk, crystal or ceramic resonator dedicated for TOD operation. interrupt and isochronous transfers. Oscillator (XOSC2) for high frequency crystal input for MCG ADC12 12-bit Successive approximation ADC with up to 4 reference to be used for system clock and USB operations. dedicated differential channels and 8 single-ended channels Multipurpose Clock Generator (MCG) PLL and FLL precision range compare function 1.7 mV/C temperature sensor internal trimming of internal reference allows 0.2% resolution and 2% bandgap reference channel operation in stop3 fully functional deviation over temperature and voltage supports CPU from 3.6V to 1.8V, Configurable hardware trigger for 8 Channel frequencies from 4 kHz to 48 MHz. select and result registers System Protection PDB Programmable delay block with 16-bit counter and Watchdog computer operating properly (COP) reset Watchdog modulus and prescale to set reference clock to bus divided by 1 to computer operating properly (COP) reset with option to run from bus divided by 2048 8 trigger outputs for ADC12 module provides dedicated 1-kHz internal clock source or bus clock periodic coordination of ADC sampling sequence with sequence Low-voltage detection with reset or interrupt selectable trip points completion interrupt Back-to-Back mode and Timed mode separate low-voltage warning with optional interrupt selectable DAC 12-bit resolution 16-word data buffers with configurable trip points watermark. Illegal opcode and illegal address detection with reset Input/Output Flash block protection for each array to prevent accidental Up to 47 GPIOs and 2 output-only pin and 1 input-only pin. write/erasure Voltage Reference output (VREFO). Hardware CRC to support fast cyclic redundancy checks Dedicated infrared output pin (IRO) with high current sink Development Support capability. Single-wire background debug interface Up to 16 KBI pins with selectable polarity. Real-time debug with 6 hardware breakpoints (4 PC, 1 address Package Options and 1 data) Breakpoint capability to allow single breakpoint setting 81-MBGA 10x10 mm during in-circuit debugging 80-LQFP 12x12 mm On-chip in-circuit emulator (ICE) debug module containing 3 64-LQFP 10x10 mm comparators and 9 trigger modes Peripherals CMT Carrier Modulator timer for remote control communications. Carrier generator, modulator and driver for dedicated infrared out. Can be used as an output compare timer. IIC Up to 100 kbps with maximum bus loading Multi-master operation Programmable slave address Interrupt driven This document contains information on a new product. Specifications and information herein are subject to change without notice. Freescale Semiconductor, Inc., 2009-2010. All rights reserved. Preliminary Subject to ChangeContents 2.15 VREF Specifications............................................................. 35 1 Devices in the MC9S08JE128 series.................. 3 2 Preliminary Electrical Characteristics............. 12 3 Ordering Information......................................... 41 2.1 Parameter Classification ......................................................... 12 3.1 Device Numbering System..................................................... 42 2.2 Absolute Maximum Ratings .................................................... 13 3.2 Package Information............................................................... 42 2.3 Thermal Characteristics.......................................................... 14 3.3 Mechanical Drawings ............................................................. 42 2.4 Electrostatic Discharge (ESD) Protection Characteristics ...... 15 2.5 DC Characteristics.................................................................. 16 4 Revision History................................................ 43 2.6 Supply Current Characteristics ............................................... 19 2.7 Comparator (PRACMP) Electricals......................................... 21 2.8 12-Bit Digital-to-Analog Converter (DAC12LV) Electricals...... 22 2.9 ADC Characteristics................................................................ 23 2.10 MCG and External Oscillator (XOSC) Characteristics.......... 28 2.11 AC Characteristics ................................................................ 31 2.12 SPI Characteristics ............................................................... 32 2.13 Flash Specifications.............................................................. 35 2.14 USB Electricals ..................................................................... 36 Related Documentation Find the most current versions of all documents at: