NXP Semiconductors KE1xFP100M168SF0 Data Sheet: Technical Data Rev. 4, 06/2019 Kinetis KE1xF with up to 512 KB MKE1xF512VLL16 MKE1xF512VLH16 Flash MKE1xF256VLL16 Up to 168 MHz ARM Cortex-M4 Based Microcontroller MKE1xF256VLH16 The KE1xF microcontroller is built on the ARM Cortex -M4 processor with stronger performance and higher memory densities in multiple packages. This device offers up to 168 MHz performance with integrated single-precision floating point unit (FPU) and digital signal processor (DSP). Embedded flash memory sizes range from 256 KB to 512 KB. 100 LQFP (LL) 64 LQFP (LH) 14x14x1.4 mm Pitch 10x10x1.4 mm Pitch 0.5 mm 0.5 mm Core Processor and System Memory and memory interfaces ARM Cortex -M4 core, supports up to 168 MHz Up to 512 KB program flash with ECC frequency with 1.25 Dhrystone MIPS per MHz Up to 64 KB SRAM with ECC ARM Core based on the ARMv7 Architecture and 64 KB FlexNVM with ECC for data flash and with Thumb -2 ISA EEPROM emulation Integrated Digital Signal Processor (DSP) 4 KB FlexRAM for EEPROM emulation Configurable Nested Vectored Interrupt Controller 8 KB I/D cache to minimize performance impact of (NVIC) memory access latencies Single-precision Floating Point Unit (FPU) Boot ROM with built in bootloader 16-channel DMA controller extended up to 64 channels Mixed-signal analog with DMAMUX 3 12-bit analog-to-digital converter (ADC) with up Reliability, safety and security to 16 channel analog inputs per module, up to 1M Error-correcting code (ECC) on Flash and SRAM sps memories 3 high-speed analog comparators (CMP) with System memory protection unit (MPU) module internal 8-bit digital to analog converter (DAC) Flash Access Control (FAC) 1 12-bit digital to analog converter (DAC) Cyclic Redundancy Check (CRC) generator module Timing and control 128-bit unique identification (ID) number 4 Flex Timers (FTM) for PWM generation, offering Internal watchdog (WDOG) with independent clock up to 32 standard channels source 1 Low-Power Timer (LPTMR) working at Stop External watchdog monitor (EWM) module mode, with flexible wake up control ADC self calibration feature 3 Programmable Delay Block (PDB) with flexible On-chip clock loss monitoring trigger system, to provide accurate delay and trigger Human-machine interface (HMI) generation for inter-module synchronization Supports up to 92 interrupt request (IRQ) sources 1 Low-power Periodic Interrupt Timer (LPIT) with 4 Up to 89 GPIO pins with interrupt functionality independent channels, for general purpose 8 high drive pins Pulse Width Timer (PWT) Digital filters Real timer clock (RTC) NXP reserves the right to change the production detail specifications as may be required to permit improvements in the design of its products.Clock interfaces Connectivity and communications interfaces 4 - 40 MHz fast external oscillator (OSC) TriggerMUX: for module inter-connectivity 32 kHz slow external oscillator (OSC32) 3 low-power universal asynchronous receiver/ 48 MHz high-accuracy (up to 1%) fast internal transmitter (LPUART) modules with DMA support reference clock (FIRC) for high-speed run and working at Stop mode 8 MHz / 2 MHz high-accuracy (up to 3%) slow internal 2 low-power serial peripheral interface (LPSPI) reference clock (SIRC) for low-speed run modules with DMA support and working at Stop 128 kHz low power oscillator (LPO) mode Phased lock loop (PLL) 2 low-power inter-integrated circuit (LPI2C) Up to 50 MHz DC external square wave input clock modules with DMA support and working at Stop System clock generator (SCG) mode Real time counter (RTC) Up to 2 FlexCAN modules, with flexible message buffers and mailboxes Power management FlexIO module for flexible and high performance Low-power ARM Cortex-M4 core with excellent energy serial interfaces emulation efficiency Power management controller (PMC) with multiple Debug functionality power modes: HSRun, Run, Wait, Stop, VLPR, VLPW Serial Wire JTAG Debug Port (SWJ-DP) combines and VLPS Debug Watchpoint and Trace (DWT) Supports clock gating for unused modules, and specific Instrumentation Trace Macrocell (ITM) peripherals remain working in low power modes Test Port Interface Unit (TPIU) POR, LVD/LVR Flash Patch and Breakpoints (FPB) Operating Characteristics Voltage range: 2.7 to 5.5 V Ambient temperature range: 40 to 105 C Related Resources Type Description Resource 1 Product Brief The Product Brief contains concise overview/summary information to KE1xF512PB enable quick evaluation of a device for design suitability. 1 Reference The Reference Manual contains a comprehensive description of the KE1xFP100M168SF0RM Manual structure and function (operation) of a device. Data Sheet The Data Sheet includes electrical characteristics and signal This document: connections. KE1xFP100M168SF0 1 Chip Errata The chip mask set Errata provides additional or corrective information for Kinetis E 0N79P a particular device mask set. Package Package dimensions are provided in package drawings. 100-LQFP: 98ASS23308W drawing 64-LQFP: 98ASS23234W 1. To find the associated resource, go to