TDF8546AJ/N1,112 NXP

TDF8546 2 I C-bus controlled 4 45 W best efficiency amplifier Rev. 8 27 September 2013 Product short data sheet 1. General description The TDF8546 is one of a new generation of complementary quad Bridge-Tied Load (BTL) audio power amplifiers intended for automotive applications. It has a best efficiency mode 2 with full I C-bus controlled diagnostics, including start-up diagnostics. The TDF8546 can operate at a battery voltage as low as 6 V making this amplifier suitable for stop/start-car operation. The new best efficiency principle uses a patented switch technique which reduces switching distortion. To reduce power dissipation, the new best efficiency principle uses the audio information on all four channels instead of only the front or rear signals. Dissipation is more than 65 % less than standard BTL when used for front and rear correlated audio signals. Dissipation is 35 % less than standard BTL when used for uncorrelated (delayed) audio signals between front and rear. It is 17 % less for uncorrelated audio signals when the front or rear information is used. The amplifier uses a complementary DMOS output stage in a Silicon-On-Insulator (SOI) based BCD process. The DMOS output stage ensures a high-power output signal with perfect sound quality. The SOI-based BCD process ensures a robust amplifier, where latch-up cannot occur, with good separation between the four independent channels, with every component isolated and without substrate currents. 2. Features and benefits Stop/start-car prepared: keeps operating without audible disturbance during engine start at a battery voltage as low as 6 V New best efficiency mode with patented low switching distortion Extreme best efficiency mode (uses information from 4 channels) with 17 % less dissipation for uncorrelated signals compared to 2-channel best efficiency mode. 2 2 Operates in either legacy (non-I C-bus) or I C-bus modes (3.3 V and 5 V compliant) 2 Four hardware-programmable I C-bus addresses Can drive 2 and 4 loads Speaker fault detection Start-up diagnostics with load detection: open, short, present filtered for door-slam and chatter relays AC load (tweeter) detection with low and high current mode Gain select after start-up without audible disturbance Independent selectable soft mute of front and rear channels Programmable gain (26 dB and 16 dB), independently programmable for the front and rear channelsTDF8546 NXP Semiconductors 2 I C-bus controlled 4 45 W best efficiency amplifier Line driver mode supports engine start at a battery voltage as low as 6 V (16 dB and mid-tap voltage 0.25 V ) P Programmable clip detect: 2 %, 5 % or 10 % Programmable thermal pre-warning Pin STB can be programmed/multiplexed with second-clip detect Clip information of each channel can be directed separately to pin DIAG or pin STB Independent enabling of thermal-, clip- or load fault information (short across the load or to V or to ground) on pin DIAG P Loss-of-ground and open V safe (minimum series resistance required) P All amplifier outputs short-circuit proof to ground, supply voltage and across the load (channel independent) All pins short-circuit proof to ground Temperature controlled gain reduction to prevent audio holes at high junction temperatures Programmable low battery voltage detection to enable 7.5 V or 6 V minimum battery voltage operation Overvoltage protection (load-dump safe up to V = 50 V) with overvoltage pre-warning P at 16 V Offset detection 3. Quick reference data Table 1. Quick reference data Symbol Parameter Conditions Min Typ Max Unit V operating supply R = 4 614.4 18 V P(oper) L voltage quiescent current no load - 260 350 mA I q = 7 V - 190 - mA no load V P output power R =4 V = 14.4 V maximum power 37 40 - W P o L P V = 2 V RMS square wave i R =4 V = 15.2 V maximum power 41 45 - W L P V = 2 V RMS square wave i R =4 V = 14.4 V THD = 0.5 % 18 20 - W L P R =4 V = 14.4 V THD = 10 % 23 25 - W L P R =2 V = 14.4 V THD = 10 % 40 44 - W L P R =2 V = 14.4 V maximum power 58 64 - W L P V = 2 V RMS square wave i = 1 W to 12 W f = 1 kHz R =4 BTL mode - 0.01 0.1 % THD total harmonic P o i L distortion =4W f = 1 kHz R =4 best efficiency mode - 0.03 - % P o i L output noise voltage filter 20 Hz to 22 kHz R =1k V n(o) S amplifier mode - 43 65 V line driver mode - 25 33 V TDF8546 SDS All information provided in this document is subject to legal disclaimers. NXP B.V. 2013. All rights reserved. Product short data sheet Rev. 8 27 September 2013 2 of 21