Ordering number : ENA1972B
LV5695P
Bi-CMOS IC
LV5695P
Specifications
Absolute Maximum Ratings at Ta = 25C
Parameter Symbol Conditions Ratings Unit
Power supply voltage V max 36 V
CC
Power dissipation Pd max IC unit 1.5 W
3
(*1) At using Al heat sink (50501.5mm) 5.6W
At infinity heat sink 32.5 W
Peak voltage V peak Regarding Bias wave, refer to below the pulse. 50 V
CC
Operating temperature Topr -40 to +85 C
Storage temperature Tstg -55 to +150 C
Junction temperature Tj max 150 C
*1 : Ta 25C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed,
damage may occur and reliability may be affected.
Recommended Operating Conditions at Ta = 25C
Parameter Conditions Ratings Unit
Power supply voltage rating 1 V output ON, SWD output ON 7 to 16 V
DD
Power supply voltage rating 2 ILM output ON 10.3 to 16 V
Power supply voltage rating 3 Audio output ON, CD output ON 10 to 16 V
* V 1 should be as follows: V 1>V -0.7V
CC CC CC
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended
Operating Ranges limits may affect device reliability.
Electrical Characteristics at Ta = 25C(*2), V = V 1=14.4V
CC CC
Ratings
Parameter Symbol Conditions Unit
min typ max
Current drain I V no load, CTRL1/2/3 = L/L/L 50 100 A
CC DD
CTRL1/2/3 Input
Low input voltage V1 0 0.3 V
IL
Middle input voltage 1 V1 0.8 1.06 1.4 V
IM
Middle input voltage 2 V2 1.9 2.13 2.4 V
IM
High input voltage V 2.9 3.2 5.5 V
IH
Input impedance R Input voltage 3.3V 280 400 520 k
IN
IKV input.
DD
Low input voltage V2 - - 0.7 V
IL
High input voltage V2 IKV V1-0.7 - - V
IH DD CC
V output(5V/3.3V)
DD
Output voltage V11 I 1 = 200mA, IKV = V1 4.855.0 5.15V
O O DD CC
V12 I 1 = 200mA, IKV = GND 3.2 3.3 3.4 V
O O DD
Output current I1 V 11 4.7V, V 12 3.1V 300 mA
O O O
Line regulation V 1 7.5V < V 1 < 16V, I 1 = 200mA 30 70 mV
OLN CC O
Load regulation V 1 1mA < I 1 < 200mA 70 150 mV
OLD O
Dropout voltage 1 V 1 I 1 = 200mA (V output 5V time) 0.8 1.6 V
DROP O DD
Dropout voltage 2 V 1 I 1 = 100mA (V output 5V time) 0.4 0.8 V
DROP O DD
Ripple rejection R 1 f = 120Hz, I 1 = 200mA 30 40 dB
REJ O
AUDIO (8.45V) Output ; CTRL2 = M1 or H
AUDIO output voltage 1 V3 I 3 = 650mA 8.196 8.45 8.7 V
O O
AUDIO output current I3 V 3 8.0V 800 mA
O O
Line regulation V 3 10V < V < 16V, I 3 = 650mA 30 90 mV
OLN CC O
Load regulation V 3 1mA < I 3 < 650mA 100 200 mV
OLD O
Dropout voltage 1 V 3 I 3 = 650mA 0.7 1.2 V
DROP O
Dropout voltage 2 V 3 I 3 = 200mA 0.2 0.35 V
DROP O
Ripple rejection R 3 f = 120Hz, I 3 = 650mA 40 50 dB
REJ O
Continued on next page.
No.A1972-2/14