NCP718AMT330TBG ON Semiconductor

Low Dropout Regulator, Wide Input Voltage, Low Iq, 300 mA NCP718 The NCP718 is 300 mA LDO Linear Voltage Regulator. It is a very stable and accurate device with ultralow quiescent current www.onsemi.com consumption (typ. 4 A over the full temperature range) and a wide input voltage range (up to 24 V). The regulator incorporates several protection features such as Thermal Shutdown and Current Limiting. MARKING DIAGRAMS Features WDFN6 1 Operating Input Voltage Range: 2.5 V to 24 V MT SUFFIX XX M CASE 511BR Fixed Voltage Options Available: 1.2 V to 5 V (upon request) 1 Adjustable Voltage Option from 1.2 V to 5 V XX = Specific Device Code M = Date Code UltraLow Quiescent Current: typ. 4 A over Temperature 2% Accuracy Over Full Load, Line and Temperature Variations TSOT235 PSRR: 60 dB at 1 kHz XX M SN SUFFIX CASE 419AE Noise: typ. 36 V from 100 Hz to 100 kHz 1 RMS 1 Stable with Small 1 F Ceramic Capacitor XX = Specific Device Code Softstart to Reduce Inrush Current and Overshoots M = Date Code* Thermal Shutdown and Current Limit Protection = PbFree Package SOA Limiting for High Vin / High Iout Static / Dynamic (Note: Microdot may be in either location) Active Discharge Option Available (upon request) *Date Code orientation and/or position may Available in TSOT235 and WDFN6 2x2 mm Packages vary depending upon manufacturing location. These Devices are PbFree, Halogen Free/BFR Free and are RoHS Compliant PIN CONNECTIONS Typical Applications 1 6 Wireless Chargers OUT IN Portable Equipment 2 5 NC/ADJ GND NC Communication Systems 3 4 GND EN V V IN OUT WDFN6 2x2 mm IN OUT (Top View) NCP718 1 F F 1 C IN C OUT EN Ceramic NC Ceramic GND ON IN OUT OFF GND Figure 1. Typical Application Schematic NC/ADJ EN TSOT235 (Top View) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 7 of this data sheet. Semiconductor Components Industries, LLC, 2017 1 Publication Order Number: September, 2019 Rev. 9 NCP718/DNCP718 IN IN ENABLE THERMAL ENABLE THERMAL EN EN LOGIC SHUTDOWN LOGIC SHUTDOWN BANDGAP BANDGAP MOSFET MOSFET REFERENCE REFERENCE INTEGRATED INTEGRATED DRIVER WITH DRIVER WITH SOFTSTART SOFTSTART CURRENT LIMIT CURRENT LIMIT OUT OUT ADJ * ACTIVE DISCHARGE * ACTIVE DISCHARGE Version A only Version A only EN EN GND GND Fixed Version Adjustable Version Figure 2. Simplified Block Diagram Table 1. PIN FUNCTION DESCRIPTION Pin No. Pin No. (WDFN6) (TSOT235) Pin Name Description 6 1 IN Input pin. A small capacitor is needed from this pin to ground to assure stability. 3, EXP 2 GND Power supply ground. 4 3 EN Enable pin. Driving this pin high turns on the regulator. Driving EN pin low puts the regulator into shutdown mode. 2 4 NC / ADJ Fixed Version: No connection. This pin can be tied to ground to improve thermal dissipation or left disconnected. Adjustable Version: Feedback pin for setup output voltage. Use resistor divider for voltage selection. 1 5 OUT Regulated output voltage pin. A small 1 F ceramic capacitor is needed from this pin to ground to assure stability. 5 N/C No connection. This pin can be tied to ground to improve thermal dissipation or left dis- connected. Table 2. ABSOLUTE MAXIMUM RATINGS Rating Symbol Value Unit Input Voltage (Note 1) V 0.3 to 24 V IN Enable Voltage V 0.3 to V V EN IN+0.3 Output Voltage V 0.3 to V (max. 6) V OUT IN+0.3 Output Short Circuit Duration t Indefinite s SC Maximum Junction Temperature T 150 C J(MAX) Storage Temperature T 55 to 150 C STG ESD Capability, Human Body Model (Note 2) ESD 2000 V HBM ESD Capability, Charged Device Model (Note 2) ESD 1000 V CDM Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area. 2. This device series incorporates ESD protection and is tested by the following methods: ESD Human Body Model tested per AECQ100002 (EIA/JESD22A114) ESD Charged Device Model tested per EIA/JESD22C101, Field Induced Charge Model. Latch up Current Maximum Rating tested per JEDEC standard: JESD78. Latchup is not guaranteed on ENABLE pin. Table 3. THERMAL CHARACTERISTICS Rating Symbol Value Unit Thermal Characteristics, WDFN6, 2 mm x 2 mm R 65 C/W JA Thermal Resistance, JunctiontoAir Thermal Characteristics, TSOT235 R 235 C/W JA Thermal Resistance, JunctiontoAir www.onsemi.com 2