NCP81071CZR2G ON Semiconductor

Dual 5 A High Speed Low-Side MOSFET Drivers with Enable NCP81071 NCP81071 is a high speed dual lowside MOSFETs driver. It is capable of providing large peak currents into capacitive loads. This www.onsemi.com driver can deliver 5 A peak current at the Miller plateau region to help reduce the Miller effect during MOSFETs switching transition. This MARKING DIAGRAMS driver also provides enable functions to give users better control capability in different applications. ENA and ENB are implemented 8 on pin 1 and pin 8 which were previously unused in the industry XXXX SOIC8 ALYW standard pinout. They are internally pulled up to drivers input D SUFFIX voltage for active high logic and can be left open for standard CASE 751 1 operations. This part is available in MSOP8EP package, SOIC8 package and WDFN8 3 mm x 3 mm package. XXXX Features AYW MSOP8 High Current Drive Capability 5 A Z SUFFIX TTL/CMOS Compatible Inputs Independent of Supply Voltage CASE 846AM Industry Standard Pinout High Reverse Current Capability (6 A) Peak 1 1 XX M Enable Functions for Each Driver WDFN8 8 ns Typical Rise and 8 ns Typical Fall Times with 1.8 nF Load MN SUFFIX CASE 511CD Typical Propagation Delay Times of 20 ns with Input Falling and 20 ns with Input Rising XX = Specific Device Code Input Voltage from 4.5 V to 20 V A = Assembly Location L = Wafer Lot Dual Outputs can be Paralleled for Higher Drive Current Y = Year These Devices are PbFree, Halogen Free/BFR Free and are RoHS W = Work Week Compliant M = Date Code = PbFree Package Applications (Note: Microdot may be in either location) Server Power Telecommunication, Datacenter Power PIN CONNECTIONS Synchronous Rectifier 1 8 Switch Mode Power Supply ENA ENB DC/DC Converter INA OUTA Power Factor Correction VDD GND Motor Drive OUTB INB Renewable Energy, Solar Inverter (Top View) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 11 of this data sheet. Semiconductor Components Industries, LLC, 2016 1 Publication Order Number: March, 2021 Rev. 4 NCP81071/DNCP81071 VDD VDD VDD VDD ENA VDD ENA VDD Ref Ref Logic Logic VDD VDD VDD A Channel A Channel OUTA OUTA INA INA VDD VDD Ref Ref VDD VDD VDD VDD UVLO UVLO ENB OUTB ENB OUTB Ref Ref Logic Logic VDD B Channel B Channel INB GND INB GND Ref Ref NCP81071A NCP81071B VDD VDD ENA VDD Ref Logic VDD VDD A Channel OUTA INA VDD Ref VDD VDD UVLO ENB OUTB Ref Logic B Channel INB GND Ref NCP81071C Figure 1. NCP81071 Block Diagram Table 1. PIN DESCRIPTION Pin No. Symbol Description 1 ENA Enable input for the driver channel A with logic compatible threshold and hysteresis. This pin is used to en- able and disable the driver output. It is internally pulled up to VDD with a 200 k resistor for active high op- eration. The output of the pin when the device is disabled will be always low. 2 INA Input of driver channel A which has logic compatible threshold and hysteresis. If not used, this pin should be connected to either VDD or GND. It should not be left unconnected. 3 GND Common ground. This ground should be connected very closely to the source of the power MOSFET. 4 INB Input of driver channel B which has logic compatible threshold and hysteresis. If not used, this pin should be connected to either VDD or GND. It should not be left unconnected. 5 OUTB Output of driver channel B. The driver is able to provide 5 A drive current to the gate of the power MOSFET. 6 VDD Supply voltage. Use this pin to connect the input power for the driver device. 7 OUTA Output of driver channel A. The driver is able to provide 5 A drive current to the gate of the power MOSFET. 8 ENB Enable input for the driver channel B with logic compatible threshold and hysteresis. This pin is used to en- able and disable the driver output. It is internally pulled up to VDD with a 200 k resistor for active high op- eration. The output of the pin when the device is disabled will be always low. www.onsemi.com 2