Light Touch Switches/EVPBB 2.6 mm1.6 mm SMD Light Touch Switches Type: EVPBB Features External dimensions: 2.6 mm 1.6 mm, Height 0.50 mm, 0.53 mm, 0.55 mm High operability Equipped with an actuator (push plate) IP67 Recommended Applications Opearation switches for Smartphone, Wearable devices (Smartwatch, Headset, Hearing aid) Explanation of Part Numbers 1 2 345678 9 10 11 12 A B 000 Product Code Type Operating Characteristic Force Specications Type Snap action/Push-on type SPST Rating 10 A 2 V DC to 20 mA 15 V DC (Resistive load) Contact Resistance 500 m max. Electrical Insulation Resistance 50 M min. (at 100 V DC) Dielectric Withstanding Voltage 250 V AC for 1 minute Bouncing 10 ms max. (ON, OFF) Operating Force 0.7 N 1.0 N 1.6 N, 2.4 N Mechanical Travel 0.08 mm 0.08 mm 0.11 mm Endurance Operating Life 200,000 cycles min. 500,000 cycles min. Dust resistance : 4 types of talc 8 h, Protective Structure IP67( 1) Water resistance : Immersion depth 1 m 30 min. Operating Temperature 40 C to +85 C 40 C to +85 C (Bulk) Storage Temperature 20 C to +60 C (Taping) Minimum Quantity/Packing Unit 10,000 pcs. Embossed Taping (Reel Pack) Quantity/Carton 50,000 pcs. Note: Non washable ( 1) IP67 : Switch shall not be operated during test. Water or dust ingress shall be limited enough to prevent deleterious effect to the switch function. However, IP67 shall be guaranteed under single product state, then there is a possibility that IP67 performance become impaired depending on your mounting condition or usage. So, please ask us in advance, if the switch is applied to important usage for water and dust resistant. LQGXVWULDO SDQDVRQLF FRP DF H 1 Light Touch Switches/EVPBB Dimensions in mm (not to scale) EVPBB Embossed Taping) ( General dimension tolerance : 0.05 ( )dimensions are reference dimensions. H0.1 0.35 B A CC A B 0.05min. 2-1.8 0.91 A B 0.7 B A Circuit diagram 2-3.1 Actuator cross section Section C-C 2-2.2 2.60.1 Without the film 30.1 Stencil mask plan 2-3.2 2-2.1 A B No soldering A B 2 Land pattern plan Soldering thickness t=0.080.01 Soldering failure may occur depending on applied solder amount,so, please consider to use our recommended stencil and land pattern desing :Recommended land pattern area :No soldering area Any land pattern or via holes shall not be provided at area. If it s necessary to design land pattern or via holes at area, please apply resist to them to protect their metal part completely. If their metal parts are not protected completely, short circuit failure may occur by solder ball. Besides, there should be convexoconcave by designing additional pattern, it may cause swith tilt, influence on solder-ability or flux intrusion after reflow soldering. Therefore, please study any influence of additional land pattern or via holes at area in advance. Part Numbers Operating Force H=Height Operating Life EVPBB0AAB000 0.7 N 0.50 mm 200,000 cycles EVPBB1AAB000 1.0 N 0.50 mm 500,000 cycles EVPBB2A9B000 1.6 N 0.53 mm 500,000 cycles EVPBB4A9B000 2.4 N 0.55 mm 500,000 cycles 2 4-0.35 2-0.1max. 0.025 2-0.75 1.6 2-0.85 1.60.1 without the film and remainder of the gate 2-0.3 2-0.2 2-1.2 2-1.3