4263-B 3. Part Names CAUTION NOTE V95100136 Be sure the power is disconnected before installing this product. Failure to comply may result in electric shock. Even when starting two or more unitis simultaneously, a lag will occur during message playback. Volume Installation Bracket Ensure the installation surface is sufficient enough to handle the weight of the product, and Air Vents where there is less vibration. Also, do not install onto a vehicle. Failure to comply will lead to Slim Model MP3 Voice Annunciator injury or damage to the product. Cover Locking 6. Specifications Use two screws when installing and tighten with the recommended torque. Failure to comply Instruction Manual Hole may result in product failure due to falling or over-torquing. TYPE : BSV Items Specifications Do not apply a heavy load to the wires. Failure to comply may result in damage due to an electric short. o Do not turn the front cover more than 45 . Failure to comply may result in product damage. Rated Voltage DC 12 to 24V Voltage Range DC 10.8 to 26.4V Thank you for purchasing the Slim Model MP3 Voice (*1) Power Consumption Max. 3.5W PLEASE (*2) Annunicator for you application. Please read these instructions Sound Pressure Level 87dB or less: (For Panel Mount) / 85dB or less: (For Wall Mount) Install the product on a flat surface with no uneven surfaces. Failure to comply will weaken its Volume Adjustable carefully before installation, maintenance and repair. Store this resistance to water and dust. Volume Control Sound Reduction Function: -1dB to -50dB range possible from the CH4 input Front Cover O-ring If installing the product where vibrations exist, it is recommended to make periodic inspections manual in a safe place for future reference. If you have any questions Power/ Signal Wiring (*3) to ensure the mounting screws are properly tightened. Number of Playback Messages Bit Input: 5 (4) / Binary Input: 31 (7) Mounting Screw SD Card Slot regarding this product, please contact our PATLITE Sales When installing in high places, choose a location which is accessible by a scaffold, ladder, etc., for repairs. The following alarm data is loaded when no set messages are ordered When operating the product by controlling the power ON/OFF, be sure to include a switch by Front Cover Exploded View No. 1 Chime No. 2 Beep No. 3 Stutter No. 4 Bell No. 5 Yelp Representatives. Initial Registered Data which the power supply can be easily cut near the main power for safety. No. 6 Rapid Hi Lo No. 7 Melody Chime No. 8 Synthesized Piano No. 9 Synthesized Bell No. 10 Stutter + Bell Do not block any air vents when installing this product. No. 11 Synthesized Melody No. 12 Call Sign No. 13 Inverted Reveille No. 14 Galactic Motor No. 15 Two Tone Applying thread locking adhesive to the Cover locking screw may result in damage to the product. Notice for Safe Operation Audio File MPEG1 Audio Layer III (MP3) NOTE Bit Rate 32kbit/s, 64kbit/s, (Standard Rate) n order to prevent any damage to the user and other personnel or to assets, note the Maximum Playback Time Maximum Playback Time: 63sec (at Standard Bit Rate) following: SD Card Depending on the mounting surface material, thickness and the volume of the product, a vibration sound may be generated from the mounting screws. To prevent it, take countermeasure steps by reinforcing The warning indications are divided into the following classes according to the degree of danger ModelSDV-128P Internal Memory Size 508kB (MP3 data total) Accessory: M3X6 Tapping Screw (Sold Separately) the mounting screws. or damage incurred when the warning is not taken into consideration and the product is not Playback Startup Time No less than 300ms (Bootup for Signal Input and Power Input Conditions) (Cover Locking Screw) correctly used. SD Card Format: FAT16 Patlite Corporation is a member of File Format 5. Wiring the SD Card Association. Recommended SD Card: SDV-128 (Sold Separate) o o 4. Installation Operating Temperature Range Indicates an imminently dangerous condition : failure to follow the instructions may -10 C to +50 C When wiring to external contacts for the signal line, use non-voltage contacts such as a relay, Warning o o lead to death or serious injury. Storage Temperature Range switch or an NPN (PNP type also available) open collector circuit. Refer to table 1 below for contact -20 C to +60 C This product can be panel or wall mounted. Please attach in accordance with the procedure for capacity. Relative Humidity mounting after removing the front cover. 85% RH or less (No Condensation) Indicates a potentially dangerous condition: failure to follow the instructions may Caution Panel Mount Indoors: Upright, Sideways, Inverted / Outdoors: Upright Only lead to slight injury or property damage. Wiring Example 4-1. Front Cover Mounting Direction BSV-24NNPN Transistor Type When installing or adjusting the volume control to this product, please open and close the front cover in Wall Mount Indoors: Upright, Sideways, Inverted / Outdoors: None (Indoor Use Only) the following manner. Do not short Power(+) to the CH line. Failure do to so will result in damage to the product. Panel Mount IP54 (Upright Direction Only) Protection Rating Turn the front cover in the counter clockwise direction 45 degrees. Assure there is ample rotation Indicates something to observe before using this product. The disregard to this Wall Mount IP20 PLEASE space available for the front cover when mounting. CH4 Light Green indication may lead to product malfunction or failure. CH4 Insulation Resistance More than 1M at 500V DC between the terminals and chassis When attaching for wall-mounting, pull the front cover forward to remove, then pull-out the mounting screw and O-ring. (Refer to3. Part Name for the Front Cover Exploded View) CH3 Peach CH3 Withstanding Voltage 500VAC applied for 1 minute between terminals and chassis without breaking insulation Notice regarding supplementary information or convenient explanation is NOTE Please attach the removed parts in steps and in the reverse order to reassemble. Attach the 2 indicated. Vibration Resistance 70m/s at 30Hz in the X, Y and Z directions for 2 hours each front cover so that theU is on top. (Mounting Screw Recommended Torque: 0.3 N-m) CH2 Yellow CH2 Mass ( 100g Use the M3X6 tapping screw (Cover Locking Screw-included) indicated on the lower-right figure to fix CH1 Sky Blue the front cover. (Recommended Torque: 0.3 N-m) CH1 1. To operate this product properly, observe the following: (*1) Test Conditions: DC24V, Max. Vol., Ch 1 to 4 on, 1kHz sine wave at -1dB Volume mm Attach the front cover so that the Cover Locking Screw 2 (*2) Test Conditions: Placed on a 300mm base at a distance of 1 meter with a 1kHz sine wave at a -6dB input. (100) arrow is alligned as indicated. Power (-) Black Power (-) Sound level of message will vary with the surrounding environment. WARNING (*3) Values in brackets indicate available channels when sound reduction function is used Fuse Fuse Power (+) White Power (+) Be sure the power is disconnected before wiring or installing this product. Possibility of electric shock Outer Appearance may occur. Non-voltage Contact Circuit NPN Transistor Circuit Do not disassemble or modify this product. Possibility of fire or electric shock may occur. If repair is (mm) Wiring Example needed, refer to 8. Before Requesting Repair . For questions concerning our product or for when 75 19.9 67.6 BSV-24PPNP Transistor Type repair is necessary, refer to the end of this document for contacting your nearest PATLITE Sales Do not short Power(-) to the CH line. Failure do to so will result in damage to the product. Representative. Be careful not to miswire this product. Possible miswiring can cause product failure or fire. CH4 Light Green CH4 Open Be sure to stay within the operating voltage range. Possibility of fire, failure or malfunction may occur. Cover Locking Request the installation and wiring be performed by a professional contractor. Otherwise, there is the Hole CH3 CH3 Peach Mounting Screw possibility that fire, electric shock or falling from high places may result. CH2 Yellow CH2 4-2. Panel Mounting Mount on a flat surface with a panel thickness of 1 mm to 3.5 mm for proper clamping. (Refer to the CH1 Sky Blue CH1 CAUTIONPanel-mount Dimension drawin) 7 To protect the power supply and other internal circuitry, be sure to connect an external fuse. Rotate the front cover counter-clockwise 45 degrees, then loosen and remove the mounting screws. Power (-) Black Power (-) Check that the mounting bracket is in position (A) before inserting the product from the front, and Do not install the product in a location where vibrations exceeding the specifications exist. If installing AWG 22 UL1007 Fuse Fuse secure it with the mounting screws, clamping the mounting nut to the rear of the mounting surface. where vibrations do exist, install the product in the upright position to prevent the risk of product Power (+) White Power (+) (Recommended torque: 0.3 N-m) detaching and it falling, causing injury to a passer-by, etc. Check that the product has been properly clamped before placing the front cover back on. Voltage Contact Circuit PNP Transistor Circuit Section C Rear View Installation Surface Table 1. Signal Contact Capacity Contrary to Warnings and Cautions indicated in this document, product failure due to mishandling, +0.7 dissasembly, modifications or natural disasters, etc. is not covered by any Warranty. Moreover, Current Capacity 15mA or more Leakage Current 0.1mA or less 68 mm-0 Withstanding Voltage DC35V or more ON Voltage(V ) avoid any applications outside those indicated in this document. sat 1V or less Table 2. Recommended Fuse Rated Voltage 250V Standard Fusion Slow-blow PLEASE Rated Current 0.25A Loosen (A) Do not use in an environment exposing strong radio waves or inductance noise. Noise may be Table 3. Inrush Current Ratings induced from the speaker horn causing malfunction or failure. Inrush Current 17A Do not use in an environment where corrosive gas is present. Possible cause of failure may occur. Loosen (A) To prevent damage from static electricity, touch hands or other body parts to metals or an earth Section WARNING Panel Mounting Dimension Diagram NOTE ground to discharge the body from static charge before handling static sensitive parts, such as the C Conforms to IEC-61554 (DIN-43700) Ensure the wiring is correct before connecting the power source. Miswiring may result in SD Card. product damage. This device complies with part 15 of the FCC Rules. Use the recommended torque when attaching parts for installation, etc. Tighten (B) Operation is subject to the following two conditions: Tighten (B) When this product is used for security purposes, it should be inspected daily. In case a malfunction CAUTION (1) This device may not cause harmful interference. should occur, it is recommended that you use this product together with other security products. 4-3. Wall Mounting (2) This device must accept any interference received, including interference that may cause Be sure the power is disconnected before installing this product. Failure to comply may result in electric shock. Do not misplace parts, such as the terminal cover or front plate, while perfoming maintenance or Mount on a flat surface with a panel thickness of 1 mm to 3.5 mm for proper clamping. (Refer to the undersired operation. Do not strongly pull or tug at the wires. Failure to comply may result in damage or failure to the product. repair of the product to prevent possible damage.Panel-mount Dimension drawin) Rotate the front cover counter-clockwise 45 degrees, then loosen and remove the mounting screws and O-rings. PLEASE Despite the cautions and warnings provided in this manual, it is not the responsibility of PATLITE for - Caution on copyright - Allign the front cover with the hole positions, inserting the product from the front insert the mounting any failure or damage occured from mishandling. Work that was recorded or copied from music CDs or other media used in public To protect the power supply and other internal circuitry, be sure to connect an external fuse. screws from the back panel and tighten. (Recommended torque: 0.3 N-m) Due to changes, improvements, etc., the contents of this manual may change without advance notice. places may infringe upon copyrights and law enforcement may be imposed. Be sure to check for proper wiring before connecting the power. Ensure the product is properly installed before installing the front cover. When using a work that was recorded or copied from music CDs or other media, be To countermeasure against interference noise, make wiring as short as possible and use shielded wires sure to obtain permission from the author. whenever possible. In addition, separate any signal lines which pass along high voltage cables or is mm In addition, copyright of audio/music data distributed or sold by PATLITE Corporation susceptible to receive induction noises. Interference may influence signal inputs and cause product 0.2 57.5 belongs to PATLITE. malfunction. It is strictly prohibited to copy/reprint whole or partial contents of audio/music data If a non-voltage contact, such as a relay or switch etc., is used for the power supply line, consider inrush belonging to PATLITE Corporation, or to transfer/sell such material on computer current capacity when selecting the contact. If the capacity is insufficient, it will cause pitting or welding of the networks etc., without permission of the rightful holder. contacts, causing malfunction. 6. Directions for Operation 2-3.5 2. Model Number Configuration The following corresponds to the factory settings of this product according to the model and message registration contents at the time of order. The following applies to Model BSV-24M- - - Wall Mounting Dimension Diagram The factory setting is set for the Bit Input, and Hold Playback mode when registration data is loaded into the internal memory. (Product Front View) When message registration is up to four (4) messages: The factory setting is set for Bit Input and Normal Playback mode when registration data is loaded into the internal memory. When message registration is for five (5) messages and above: Rated Voltage Transistor Type WARNING Recorded Messages Front Cover Color The factory setting is set for Binary Input and Normal Playback mode when registration data is loaded into the internal 24: DC 12 24 V N: NPN M: Pre-recorded Messages W: Off-white Request the installation and wiring be performed by a professional contractor. Otherwise, memory. P: PNP Blank: None (15 built-in Alarms) D: Dark Grey there is the possibility that fire, electric shock or falling from high places may result. The MP3 data will play back properly when the proper transistor, bit/binary input with the signal input are integrated. S: Silver 4263-B 11.1.AUTO 71.5 5mm Sleeve 500X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for patlite manufacturer: Other Similar products are found below : LR4-BU LR5-02PJNW LR5-102WJBW-Y LR5-102WJNW-R LR6-E-B NH-WST VSST-LR6-502LJBW-RYGBC MPS-302-RYG LR4- 302LJBW-RYG LR5-02WTNU VSST-LR6-302LJBW-RYG VSST-LR6-302LJNW-RYG SZ-50L LR5-102WJNW-G LR6-02LJNW LR6- 302LJNW-RYG LR6-302PJNW-RYG VSST-LR6-502LJNW-RYGBC LR6-02PJNW LR7-02WTNU BDV-15JF-K SZK-001U LR4- 02QJNW LR4-02WJNW LR5-E-R BSV-24P-W CLA3S-24-CD LU7-E-B